This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

12mm Bearings - 12mm x 28mm axle ABEC 5 rated BLUE Rubber Sealed Sidewalls x 8

TRAMPA's own Mountain / Kite-board bearings measure 12 x 28 x 8mm & will fit to 12mm axles. They are officially known as 6001 2RS Bearings. 6001 tells you the bearings size whilst 2RS means the bearing has 2 Rubber Seals. The Rubber Seals are inserted into the Outer raceway and in contact with the inner raceway, protecting the single row of lubricated ball bearings housed within the enclosed raceways from the ingress of moisture, dust & dirt, retaining the pre-filled grease within the bearing and maintaining maxium performance to the board & rider for as long as possible. The rubber coated sidewalls are available in RED or BLUE & are embossed with the TRAMPA logo proving Top Quality!

TRAMPA's precision made steel bearings are polished to an internationally recognised ABEC 5 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 5 polishing gives you a super smooth / super fast ride which prolonges top end roll speeds. Using Bearing Reducer Spacers you are able to make these Bearings fit to 9.52mm Skate Truck Axles or 10mm Scooter Axles no problem....

All Terrain Board Bearings (12 x 28 x 8mm) BLUE sidewalls with Embossed Logo ABEC 5 6001 2RS

TRAMPA's own Mountain / Kite-board bearings measure 12 x 28 x 8mm & will fit to 12mm axles. They are officially known as 6001 2RS Bearings. 6001 tells you the bearings size whilst 2RS means the bearing has 2 Rubber Seals. The Rubber Seals are inserted into the Outer raceway and in contact with the inner raceway, protecting the single row of lubricated ball bearings housed within the enclosed raceways from the ingress of moisture, dust & dirt, retaining the pre-filled grease within the bearing and maintaining maxium performance to the board & rider for as long as possible. The rubber coated sidewalls are available in RED or BLUE & are embossed with the TRAMPA logo proving Top Quality!

TRAMPA's precision made steel bearings are polished to an internationally recognised ABEC 5 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 5 polishing gives you a super smooth / super fast ride which prolonges top end roll speeds. Using Bearing Reducer Spacers you are able to make these Bearings fit to 9.52mm Skate Truck Axles or 10mm Scooter Axles no problem....

Bearing support spacer used with 10mm O-RIng on 12mm axles - 12 x 16 x 16.5mm - LATHED

This special Spacer measures 12mm (id) x 16mm (od) x 16.5mm (long) & is known as a Bearing Support Spacer. This Bearing Support Spacer fits between the Bearings, along side the 10mm O-Ring when fitting Bearings into a TRAMPA hub when mounting the wheel onto 12mm Axles.

Over time, during the usage of your board, the bearings & spacers are put under a lot of force. Ultimately this force has to go somewhere... The Bearings use a Steel ring in their assembly where as the Bearing Support Spacers are made from Aluminum. Steel is much stronger than Aluminum & when forced against each the aluminum will loose out every time! This is what happens to your spacers between the bearings, the Bearings put force onto your spacers as a consequence over time the spacers shrink... With enough time its possible for an annoying rattle to start.... That's when you fit these 16.5mm spacers with the little 10mm O-Rings to prevent the rattles!! :-)

Rubber O-Ring to fit in Bearings - 2mm Section x 10mm Bore NITRILE 70

This O-Ring should be fitted when a 12 x 16.5mm Bearing Support Spacer is fitted into the wheel assembly when fitting a wheel onto 12mm Axles.

It fits alongside the Bearing Support Spacer, in-between the Bearings. This O-Ring prevents rattles from the spacer against the bearings. Over time, during the usage of your board, the bearings & spacers are put under a lot of force. Ultimately this force has to go somewhere... The Bearings use a Steel ring in their assembly where as the Bearing Support Spacers are made from Aluminum. Steel is much stronger than Aluminum & when forced against each the aluminum will loose out every time! This is what happens to your spacers between the bearings, the Bearings put force onto your spacers as a consequence over time the spacers shrink... With enough time its possible for an annoying rattle to start.... That's when you fit these little O-Rings!! :-)

TRAMPA's own Mountain / Kite-board bearings measure 12 x 28 x 8mm & will fit to 12mm axles. They are officially known as 6001 2RS Bearings. 6001 tells you the bearings size whilst 2RS means the bearing has 2 Rubber Seals. The Rubber Seals are inserted into the Outer raceway and in contact with the inner raceway, protecting the single row of lubricated ball bearings housed within the enclosed raceways from the ingress of moisture, dust & dirt, retaining the pre-filled grease within the bearing and maintaining maxium performance to the board & rider for as long as possible. The rubber coated sidewalls are available in RED or BLUE & are embossed with the TRAMPA logo proving Top Quality!

TRAMPA's precision made steel bearings are polished to an internationally recognised ABEC 5 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 5 polishing gives you a super smooth / super fast ride which prolonges top end roll speeds. Using Bearing Reducer Spacers you are able to make these Bearings fit to 9.52mm Skate Truck Axles or 10mm Scooter Axles no problem....

TRAMPA ABEC 5 6001 2RS All Terrain Board Bearings - BLUE
Bearing support spacer used with 10mm O-RIng on 12mm axles
Anti Vibration Rubber O-Ring for 12mm Axles
Bearing Inner Diameter (Axle thickness) - 12mm
Bearing Outer Diameter (Hub Housing width) - 28mm
Bearing Tickness (Seating depth) - 8mm
Weight: 177g

Quantity required:
RRP £17.50 - per set of 8

RRP Includes 20% VAT

Non-EU customers purchase tax-free

Approx price :
Approx. shipping price:

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon