This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

9.525mm Bearings - 9.55mm x 28mm (3/8ths UNC imperial) axle ABEC 5 rated RED x 8

9.525mm Bearings - 9.55mm x 28mm (3/8ths UNC imperial) axle ABEC 5 rated RED x 8 9.525mm Bearings - 9.55mm x 28mm (3/8ths UNC imperial) axle ABEC 5 rated RED x 8 12mm Bearings - 12mm x 28mm axle ABEC 5 rated with conversion spacer x 8 RED 12mm ATB Bearings - 12mm x 28mm axle ABEC 5 rated with conversion spacers x 8 BLACK 12mm ATB Bearings - 12mm x 28mm axle ABEC 5 rated with conversion spacers x 8
RRP
£17.50
inc tax

 

URBAN CARVER Bearings (9.525 x 28 x 8mm) RED Sidewalls with Embossed Logo ABEC 5 16001 1RS

TRAMPA's 9.525mm URBAN CARVER Bearings are very special, This Bearing uses an IMPERIAL internal measurement of 3/8ths of an inch (Which when converted to metric is 9.525mm) & a METRIC External measrement of 28mm. The Bearing needs a housing depth of 8mm to seat correctly & will perfectly fit into any of the 6,  7 or 8 Inch TRAMPA HYPA or SUPERSTAR hubs / wheels onto trucks with 9.525mm (3/8ths of an Inch) axles without the need for additional bearing reducer sleeves to convert regular ATB 12mm bearings down to 9.525mm.

This spesial size of bearing is officially known as 16100 2RS. 16100 tells you the Bearings dimensions whilst 2RS means the bearing has 2 Removable Shields. The Removable Rubber Seals are contactless (friction free) & are inserted into the Outer raceway whilst in contact with the inner raceway, protecting the single row of lubricated ball bearings housed within the enclosed raceways from the ingress of moisture, dust & dirt, retaining the pre-filled grease within the bearing and maintaining maxium performance to the board & rider for as long as possible. The rubber coated sidewalls are embossed with the TRAMPA logo proving Top Quality!

TRAMPA's precision made Urban Carve bearings are polished to an internationally recognised ABEC 5 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 5 polishing gives you a super smooth / super fast ride which prolonges top end roll speeds.

TRAMPA's URBAN Carveboard bearing sets are supplied with varying sizes of Bearing Support Spacers. The spacers job is to fit between the bearings in the wheel to support the heavy loads gained through the center of the bearing centre, the centre point needs a strong connection. The spacer maintains best performance to the user for as long as possible. From time to time it is good practice for you to exchange your spacers to ensure maximum performance at all times.

Bearing support spacer used with 8mm O-RIng on 9.525mm axles 9.525 x 13.525 x 16.5mm - LATHED

This special Spacer measures 9.525mm (id) x 13.525mm (od) x 16.5mm (long) & is known as a Bearing Support Spacer. This Bearing Support Spacer fits between the Bearings, along side the 8mm O-Ring when fitting Bearings into a TRAMPA hub when mounting the wheel onto 9.525mm Axles.

Over time, during the usage of your board, the Bearings & Spacers are put under a lot of force. Ultimately this force has to and does go somewhere... The Bearings use a Steel ring in their assembly where as the Bearing Support Spacers are made from Aluminum. Steel is much stronger than Aluminum & when forced against each the aluminum will loose out every time! This is what happens to your spacers when positioned between the bearings... The Bearings put all the force into your spacers & as a consequence over time the spacers shrink...! & then with enough time its possible for an annoying rattle to start.... That's when you fit these 16.5mm spacers assited with the little 8mm O-Rings to prevent the rattles!! :-) 

The Rubber O-Ring is 2mm thick & needs to be stretched to fit onto the 9.525mm Axle. The O-Ring can be squashed slightly therefore spring back to its original shape. This tiny movement eliminates rattles

Rubber O-Ring to fit in Bearings - 2mm Section x 8mm Bore NITRILE 70

This O-Ring should be fitted when a 9.525 x 16.5mm Bearing Support Spacer is fitted into the wheel assembly when fitting a wheel onto 9.525mm Axles. It fits alongside the Bearing Support Spacer, in-between the Bearings. This O-Ring prevents rattles from the spacer against the bearings. Over time, during the usage of your board, the bearings & spacers are put under a lot of force. Ultimately this force has to go somewhere... The Bearings use a Steel ring in their assembly where as the Bearing Support Spacers are made from Aluminum. Steel is much stringer than Aluminum & when forced against each the aluminum will loose out every time! This is what happens to your spacers between the bearings, the Bearings put force onto your spacers as a consequence over time the spacers shrink... With enough time its possible for an annoying rattle to start.... That's when you fit these little O-Rings!! :-)

The following are required to build this product:

 

TRAMPA's 9.525mm URBAN CARVER Bearings are very special, This Bearing uses an IMPERIAL internal measurement of 3/8ths of an inch (Which when converted to metric is 9.525mm) & a METRIC External measrement of 28mm. The Bearing needs a housing depth of 8mm to seat correctly & will perfectly fit into any of the 6,  7 or 8 Inch TRAMPA HYPA or SUPERSTAR hubs / wheels onto trucks with 9.525mm (3/8ths of an Inch) axles without the need for additional bearing reducer sleeves to convert regular ATB 12mm bearings down to 9.525mm.

This spesial size of bearing is officially known as 16100 2RS. 16100 tells you the Bearings dimensions whilst 2RS means the bearing has 2 Removable Shields. The Removable Rubber Seals are contactless (friction free) & are inserted into the Outer raceway whilst in contact with the inner raceway, protecting the single row of lubricated ball bearings housed within the enclosed raceways from the ingress of moisture, dust & dirt, retaining the pre-filled grease within the bearing and maintaining maxium performance to the board & rider for as long as possible. The rubber coated sidewalls are embossed with the TRAMPA logo proving Top Quality!

TRAMPA's precision made Urban Carve bearings are polished to an internationally recognised ABEC 5 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 5 polishing gives you a super smooth / super fast ride which prolonges top end roll speeds.

TRAMPA's URBAN Carveboard bearing sets are supplied with varying sizes of Bearing Support Spacers. The spacers job is to fit between the bearings in the wheel to support the heavy loads gained through the center of the bearing centre, the centre point needs a strong connection. The spacer maintains best performance to the user for as long as possible. From time to time it is good practice for you to exchange your spacers to ensure maximum performance at all times.

TRAMPA ABEC 5 16001 1RS URBAN CARVER Bearings - RED
Bearing support spacer used with 8mm O-RIng on 9.525mm axles
Anti Vibration Rubber O-Ring for 9.525mm Axles
Bearing Inner Diameter (Axle thickness) - 9.525mm
Bearing Outer Diameter (Hub Housing width) - 28mm
Bearing Tickness (Seating depth) - 8mm
Weight: 177g
Which 9.525mm Bearings set do you want?
Which 9.525mm Bearings set do you want?
URBAN Carvdeboard Bearings - 9.525mm Axle URBAN Carvdeboard Bearings - 9.525mm Axle
BLUE 12mm BEARINGS & 9.525mm Bearing Reducer Sleeves BLUE 12mm BEARINGS & 9.525mm Bearing Reducer Sleeves
RED 12mm BEARINGS & 9.525mm Bearing Reducer Sleeves RED 12mm BEARINGS & 9.525mm Bearing Reducer Sleeves
BLACK 12mm BEARINGS & 9.525mm Bearing Reducer Sleeves BLACK 12mm BEARINGS & 9.525mm Bearing Reducer Sleeves
Quantity required:
We have enough parts to make…  
RRP £17.50 - per set of 8

RRP Includes 20% VAT

Non-EU customers purchase tax-free

Approx price :
Approx. shipping price:

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon