This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

TWIN Caliber II CARBON Fibre Motormount & Pulley Kit

TWIN Caliber II CARBON Fibre Motormount & Pulley Kit Caliber II CARBON Fiber Motormount with Axle support & Pulley Kit
RRP
£240
inc tax

Longboard & Skateboard Bearings (8 x 22 x 7mm) Red Black Blue White or GREEN Ceramic sidewalls ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

Longboard & Skateboard Bearings (8 x 22 x 7mm) Red Black Blue White or GREEN Ceramic sidewalls ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

M5 x 16mm Hex Head Bolt ISO 4017 Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 40mm Socket Capped Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 40mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special Bolt is specifically made for TRAMPA & is used to assemble the TRAMPA SUPERSTAR HUBS. The socket capped head of the Bolt screws neatly though the Spokes & into the fixing point in the Rim of the SUPERSTAR HUB eventually screwing  into the M4 nut on the other side easly.

Weighing just 3 grams each, they are very lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

USED FOR: 
 
SUPERSTAR HUBS
MEGASTAR HUBS

M4 x 4mm Grub Screw Marine Grade Stainless Steel - Connects the Motor Pulley onto the Motor Axle Shaft

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M6 x 8mm Grub Screw Marine Grade Stainless Steel - Locks Motor Mount to Hanger for Longboard Trucks

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M6 x 10mm Grub Screw Marine Grade Stainless Steel - Locks Motor Mount to Hanger for Longboard Trucks

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

High Torque Drive (HTD) 5M (5mm Tooth Spacing) High Power (HP) 275mm long x 15mm wide STRONGBELT - LONGBOARD Trucks #52

This is a 275mm long x 15mm wide High Torque Drive (HTD) Re-enforced Rubber Belt, which has 5mm Tooth Spacing (5M). It is a High Power rated (HP) TRANSMISSON BELT, made by the world famous German company trading as STRONGBELT. This Strongbelt is used to transfer the power from the motor, through the Motor Pulley generating movement in the slave wheel of a TRAMPA Electric Longboard.

TRAMPA opted to set a new standard in E-Skating, becoming the first in the world to fit to all of the E-Boards in its range, a 15mm wide TRANSMISSON BELT as standard! Our standard 15mm belt is almost double the width of nearly all other E-Sk8's out there, they tend to use a flimsy off the shelf 9mm transmission belt which can be prone to stretch, slip & ultimately snap. Using a re-enforced 15mm wide High Power Belt reduces stretch, eliminates slip & as a consequence provides a constantly smooth whilst incredibly intuitive power delivery direct to the rear Drive Wheels of your board. When accelerating or engine breaking (KERS), even from a standing start the STRONGBELT power is smooth & does not slip, or strain the motor, it does a damn gooood job!.....

STRONGBELT, as their name suggests, is a heavy industry brand that usually supplies the likes of Train manufacturers, where serious levels of quality with no excuses on failure are expected from the product as standard, as failure for such an item is serious as the consequences may result in death! STRONGBELT weave KEVLAR into their Pulley Belts, Kevlar is one of the strongest fibers known to man, its often added into materials to gain extra strength.... STRONGBELT have the best reputation in the Power Transmission Industry & you should expect NO stretching or snapping.

These extra quality details in the production of our electronic motor drives, provides the maximum responsiveness achievable whilst maintaining a super smooth power delivery to the rider at all times. 

12Fifties Extra wide Longboard Truck Motor Mount Truck Connector - T6 Aluminum

This simple but stylish T6 Aluminum 12FIFTIES Motor Mount Connector is specifically designed to work with TRAMPA's 12FIFTIES Extra wide Lonboard Trucks & is potentaillly compatible to fit with many similar Longboard Trucks too :-)

The Motor Mount Connector snuggly slides over the 12FIFTIES Truck Hanger & is secured tightened into position on the hanger with MARINE GRADE M6x10 grub screws.

The premium quality carbon Mounting Panel is held in position by being sandwiched between the Motor Mount Connector & the 12FIFTIES Truck Backplate. Compatible with Electric Motors with long or short Motor Axles - you’ll be able to fit pretty much any electric motor you wish but works best when accompanied with a TRAMPA motor for sure as we use a longer Motor Axle shaft whis this supported by a Motor Mount Axle shaft support housing...

Screwing through the 12FIFTIES Carbon Fibre Motor Mount panel & into an additional 12FIFTIES Backing plate holds everything in position for your motor to mount. These parts can be purchased as a kit on this link

CARBON FIBRE Longboard Motor Mount Panel for CALIBER II Truck 3K Twill weave

 

Made from 3k Twill Carbon Fibre this Caliber II Motor Mount Panel is Super strong & very lightweight.

The Caliber II Motor Mount has been CNC cut to precision shape & will fit perfectly all the motors that TRAMPA offers. This Carbon fibre Motor mount Panel will also fit many other similar sized/branded Electronic motors.

The Carbon fibre motor Mounting Panel sandwiches between the Motor Mount Connector & the Motor Mount Backplate. To Mount the Caliber II Carbon Motor Mount Panel to your Caliber II longboard Trucks you will need the Caliber Truck Motor Mount connector, 8x M6x10 grub screws, a Longboard Truck Motor Mount Clamping Disk & 4x M5x16mm Countersunk Bolts to secure the Carbon Fiber panel to the motor mount connector. These parts can be purchased as a kit on this link

Caliber II Longboard Truck Motor Mount Clamping disk for all Longboard Trucks

This simple but stylish T6 Aluminum Caliber II Motor Mount BACKPLATE is specifically designed to work with TRAMPA's Caliber II Trucks Motor Mount Connector. When fitted in positionit sandwiches the Caliber II Carbon Fiber Motor Mount Panel in the perfect position for your assembly.

Screwing through the Caliber II Carbon Fibre Motor Mount panel & into an additional Caliber II Backing plate holds everything in position for your motor to mount.

These parts can be purchased as a kit on this link

Motor Axle Support for Spring Truck Motor Mounts

This part ensures your motor is supported and the belt is running straight - two very important jobs for a smooth, fast and reliable board.

Motors with longer axles, like TRAMPA’s own, will fit perfectly into the housed bearing within, supporting the axle rotation, ensuring there is no ‘give’ in the axle, where the belt could potentially slip off at high speeds.

Fitting onto Channel Truck Motor Mounts this Motor Axle Support will work with any of the 6-9inch tyres in the TRAMPA range.

Motor Axle Support for Spring Truck Motor Mounts

This part ensures your motor is supported and the belt is running straight - two very important jobs for a smooth, fast and reliable board.

Motors with longer axles, like TRAMPA’s own, will fit perfectly into the housed bearing within, supporting the axle rotation, ensuring there is no ‘give’ in the axle, where the belt could potentially slip off at high speeds.

Fitting onto Channel Truck Motor Mounts this Motor Axle Support will work with any of the 6-9inch tyres in the TRAMPA range.

14 Tooth Aluminum Motor Pulley with 5mm Deep teeth High Torque Drive (HTD) Fits 15mm Belts onto 8mm Motor Axles

TRAMPA's 14 Tooth Motor Pulley Wheel connects directly to the Motor Axle & is secured into position using a Magnetic Fixing Key & Locking Grub Screw.

This custom made Motor Pulley Wheel uses the German Made STRONGBELT which is 15mm wide and should never stretch or break on you whilst still providing the smoothest of power deliveries to the user even from a standing start....

Changing your Motor Pulley &/or Drive pulley wheels will drastically change the performance of your ride... :-)

The KEYWAY connects between the Motor Pulley & the Motor Axle Shaft to eliminate slip under power 3x3x8mm

TRAMPA's Motor Axle Shaft to Pulley KEYWAY measures 3 x 3 x 8mm. It connects into the Motor Pulley when mounted onto the motor Axle Shaft & is used to center the pulley on the Axle & to assist in delivering all the power from the motor without slip! This KEYWAY will fit to all TRAMPA motors amongst others.

TRAMPA's Axle length measures 38.5mm (from motor housing to end of shaft) & has a Diameter of 8mm. The centre of the key (3 x 3 x 8mm) sits 16.70mm away from the Motor front. Front side of Motor to Center of Key! Deduct 4mm & you have the length from front side of motor to the start of key....

33 Tooth Slave Wheel for 83mm & 90mm Longboard Wheels SILVER - High Speed

TRAMPA's 33 Tooth Slave Wheel connects into all of TRAMPA's 83mm & 90mm Longboard Wheels perfectly! It connects through the Longboard Wheel using an Aluminum Centering Ring & M4 x 40mm Bolts with M4 M4 Nylock Nuts to lock it into position.

This custom made Slave Wheel can accept any size belt up to 17mm. TRAMPA uses's a German made 15mm wide STRONGBELT which provides a very smooth power delivery to the user, even from a standing start....

Changing your Motor Pulley &/or Slave pulley wheels will drastically change the performance characteristics of your ride... Small Pulleys at the Wheel Slows accelleration but increase's top the speed! :-)

SILVER Aluminium Centring Ring to Pulley Wheel for connecting 33 & 37 tooth pulleys to 83 & 90mm Longboard Wheels

With the use of 6x Marine Grade Stainless Steel M4x40mm Socket Capped Bolts & 6x M4 Nylock Nuts, TRAMPA's Longboard Wheel Slave Wheel CENTERING RING, which is made from Solid Aluminum, connects through & around the spokes of the 83 or 90mm Longboard Wheels, locking the Slave Wheel solid in position into the wheel & ready to be connected to the HTD (High Torque Drive) Rubber STRONGBELT to give for some super smooth, high speed electric motor action!

This simple motor mounting kit is as versatile as they come - able to work with most Longboard Trucks and wheels - as well as a variety of motor & pulley sizes. This kit comes with everything but the motor!

The Motor Mount Connectors snuggly slide over the truck hanger and are secured tightly with MARINE GRADE M6x10 grub screws. The Premium Quality Carbon Mounting Panel is sandwiched between the Motor Mount Connectors - & is fitted with a support for long motor axles. The Motor Axle Support houses a precision 608 bearing, supporting axle rotation & ensuring the motor is as secure & efficient as possible. The Motor Axle Support will only work with motors that have a long axle -  such as TRAMPA’s very own 118kv or 136kv Brushless Motors.

The Pulley Kit includes a 15mm STRONGBELT and a choice of Slave Wheels, that can drastically change the performance of your finished board. We use a 15mm wide reinforced drive belt that reduces stretch, eliminates slip & as a consequence provides a constantly smooth whilst incredibly intuitive power delivery direct to the rear Drive Wheels of your board. This kit comes with a choice of two Slave Wheels, 33 or 37 tooth, for fitting onto 83 or 90mm wheels.

---------------------------------------------------------
In this kit you get the following parts :
TRAMPA abec 7 608 or Si4n5 Ceramic Longboard & Skateboard Bearings
Motor Axle Support for Spring Truck Motor Mounts
M4 x 16mm Socket Capped Bolt - Marine Grade Stainless Steel
12Fifties Truck Motor Mount Truck Connector - T6 Aluminum
M6 x 8mm Grub Screw - Marine Grade Stainless Steel
M6 x 10mm Grub Screw - Marine Grade Stainless Steel
CALIBER II Longboard Truck CARBON Fibre Motor Mount Panel
Caliber II Longboard Truck Motor Mount Clamping disk - T6 Heat Treated
M5 x 16mm Hex Head Bolt - Marine Grade Stainless Steel
M5 Washer Form B - Marine Grade Stainless Steel
TRAMPA abec 7 608 or Si4n5 Ceramic Longboard & Skateboard Bearings
Motor Axle Support for Spring Truck Motor Mounts
M4 x 16mm Socket Capped Bolt - Marine Grade Stainless Steel
M4 x 16mm Socket Capped Bolt - Marine Grade Stainless Steel
14 Tooth Aluminum Motor Pulley - Best All Round Performance
M4 x 4mm Motor Pulley Grub Screw - Marine Grade Stainless Steel
KEYWAY for Motor Pulley & Axle Shaft - 3x 3x 8mm
33 Tooth Slave Wheel for 83mm & 90mm Longboard Wheels SILVER- High Speed
SILVER Centring Ring positions 33 & 37 Tooth Pulley to 83 & 90mm Longboard Wheels
M4 x 40mm Socket Capped Bolt - Marine Grade Stainless steel
275 x 15mm 5mm HTD Longboard STRONGBELT - NO SLIP!
Weight: 753g
What size Motor Pulleys you would like?
What size Motor Pulleys you would like?
13 Tooth - Great Hill Climber 13 Tooth - Great Hill Climber
14 Tooth - All Round gearing 14 Tooth - All Round gearing
15 Tooth - Great Top Speed 15 Tooth - Great Top Speed
What size SLAVE PULLEY do you want?
What size SLAVE PULLEY do you want?
37 Tooth - Best Hill Climber 37 Tooth - Best Hill Climber
33 Tooth - Best Top Speed 33 Tooth - Best Top Speed
Quantity required:
We have enough parts to make…  
RRP £240 - for the complete set

RRP Includes 20% VAT

Non-EU customers purchase tax-free

Approx price :
To see UPS shipping rates you need to login.

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon