This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

Carveboard Bearings R6 2RS ABEC 7 9.525mm x 22.225mm x 7.14mm x8

Carveboard Bearings R6 2RS ABEC 7 9.525mm x 22.225mm x 7.14mm  x8 Street Carveboard Bearings fits Stickies Wheels to Mini Spring Trucks R6 2RS ABEC7 9.525mm x 22.225mm x 7.14mm BLACK x 8 Street Carveboard Bearings fits Stickies Wheels to Mini Spring Trucks R6 2RS ABEC7 9.525mm x 22.225mm x 7.14mm RED x 8 Street Carveboard Bearings fits Stickies Wheels to Mini Spring Trucks R6 2RS ABEC7 9.525mm x 22.225mm x 7.14mm WHITE x 8 CERAMIC Street Carveboard Bearings fits Stickies Wheels to Mini Spring Trucks R6 2RS ABEC7 9.525mm x 22.225mm x 7.14mm WHITE x 8 STREET CARVE Bearings (9.525 x 22.225 x 7.14mm) BLACK ABEC 7 R6 2RS Carve Truck Axle CNC Spacer - 9.525 x 13.52 x 10.3mm
RRP
£20
inc tax

TRAMPA's STREET Carve Boards are very strong & being fitted with smaller wheels they can suffer a lot of abuse on hard surfaces. To compensate the the extra width & all the abuse they suffer the Mini Spring trucks are installed with thicker 9.525mm Axles than regular Skateboard or Longboard Trucks which are usually flimsy in comparison being fitted with only 8mm thick extended axles

So too make the STICKIES Longboard wheels (or any other Longboard wheels that accepts 22mm OD Bearings) fit to the 9.525mm axles of the Mini Spring Trucks you will need to use there TRAMPA R6 9.525mm ID x 22.225 OD Bearings to get them to fit. (SHOWN ABOVE) They also fit the new (so new they are not out yet) TRAMPA Extra wide Longboard Trucks!! Exciting times!!

To handle the extra forces that a wider Axle will suffer (potentially fitting an electric motor will transform the forces even further) TRAMPA decided to increase the thickness of the Axle to an imperial size of 3/8ths of an inch (this translates to Metric measurement size of 9.525mm). So in order to fit regular Longboard wheels to the Mini Spring trucks or the New TRAMPA Extra Wide Longboard Trucks you will need the special R6 2RS Bearings

Available with either RED, BLACK or WHITE embossed TRAMPA sidewalls  the R6 2RS Bearings will fit to most regular Longboard & Skateboard wheels currently on the market. R6 tells you the bearing standard size & the 2RS means the bearing has 2 Removable Sidewalls. The Removable Rubber sidewalls seal the single row of lubricated ball bearings within the Chrome Steel housings, protecting them from the elements such as dust & dirt, maintaining maximum performance to the board & rider for as long as possible. The rubber sealed sidewalls are embossed with the TRAMPA & ABEC 7 logo proving Top Quality & are removable so that you can service & clean your bearings on a regular basis maintaining high performance all of the times!

Precision made R6-2RS TRAMPA Bearings are polished to an internationally recognised ABEC-7 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 7 polishing gives you a super smooth / super fast ride which prolongs top end roll speeds.... :-)

STREET CARVE Bearings (9.525 x 22.225 x 7.14mm) BLACK ABEC 7 R6 2RS

TRAMPA's STREET BOARDS (Carveboard & Longboard) use special Bearings to fit the Longboard style wheels to the TRAMPA Mini Spring or the new TRAMPA Extra wide Longboard Trucks. To handle the extra forces a wider Axle may suffer (potentially fitting an electric motor will transform the forces) we choose to increase the size & thickness of the Axle to a new standard imperial size of 3/8ths of an inch which translates in Metric measurement size of 9.525mm. So in order to fit regular Longboard wheels to the Mini Spring trucks or the New TRAMPA Extra Wide Longboard Trucks you will need the special R6 2RS Bearings

Available with either RED, BLACK or WHITE embossed TRAMPA sidewalls  the R6 2RS Bearings will fit to most regular Longboard & Skateboard wheels currently on the market. R6 tells you the bearing standard size & the 2RS means the bearing has 2 Removable Sidewalls. The Removable Rubber sidewalls seal the single row of lubricated ball bearings within the Chrome Steel housings, protecting them from the elements such as dust & dirt, maintaining maximum performance to the board & rider for as long as possible. The rubber sealed sidewalls are embossed with the TRAMPA & ABEC 7 logo proving Top Quality & are removable so that you can service & clean your bearings on a regular basis maintaining high performance all of the times!

Precision made R6-2RS TRAMPA Bearings are polished to an internationally recognised ABEC-7 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 7 polishing gives you a super smooth / super fast ride which prolonges top end roll speeds.... :-)

Carve Truck Axle CNC Spacer - 9.525 x 13.52 x 10.3mm

Precision made to ensure an accurate fit with no rattles, this Polished9.525mm x 13.52mm x 10mm long "precision made Aluminium spacer" fits onto the axles of the Carveboard Trucks & also in-between the Bearings of the Carveboard Wheels. The Bearing Support Spacers get crushed over time from constant tightening, so check the spacer is fitting well and replace if necessary over time.

TRAMPA's STREET Carve Boards are very strong & being fitted with smaller wheels they can suffer a lot of abuse on hard surfaces. To compensate the the extra width & all the abuse they suffer the Mini Spring trucks are installed with thicker 9.525mm Axles than regular Skateboard or Longboard Trucks which are usually flimsy in comparison being fitted with only 8mm thick extended axles

So too make the STICKIES Longboard wheels (or any other Longboard wheels that accepts 22mm OD Bearings) fit to the 9.525mm axles of the Mini Spring Trucks you will need to use there TRAMPA R6 9.525mm ID x 22.225 OD Bearings to get them to fit. (SHOWN ABOVE) They also fit the new (so new they are not out yet) TRAMPA Extra wide Longboard Trucks!! Exciting times!!

To handle the extra forces that a wider Axle will suffer (potentially fitting an electric motor will transform the forces even further) TRAMPA decided to increase the thickness of the Axle to an imperial size of 3/8ths of an inch (this translates to Metric measurement size of 9.525mm). So in order to fit regular Longboard wheels to the Mini Spring trucks or the New TRAMPA Extra Wide Longboard Trucks you will need the special R6 2RS Bearings

Available with either RED, BLACK or WHITE embossed TRAMPA sidewalls  the R6 2RS Bearings will fit to most regular Longboard & Skateboard wheels currently on the market. R6 tells you the bearing standard size & the 2RS means the bearing has 2 Removable Sidewalls. The Removable Rubber sidewalls seal the single row of lubricated ball bearings within the Chrome Steel housings, protecting them from the elements such as dust & dirt, maintaining maximum performance to the board & rider for as long as possible. The rubber sealed sidewalls are embossed with the TRAMPA & ABEC 7 logo proving Top Quality & are removable so that you can service & clean your bearings on a regular basis maintaining high performance all of the times!

Precision made R6-2RS TRAMPA Bearings are polished to an internationally recognised ABEC-7 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 7 polishing gives you a super smooth / super fast ride which prolongs top end roll speeds.... :-)

TRAMPA ABEC 7 R6 2RS STREET CARVE Bearings - BLACK
Carve truck Axle CNC Spacer to fit Stickie wheels to Spring Trucks
Bearing Inner Diameter (Axle thickness) - 3/8ths Inch = 9.525mm
Bearing Outer Diameter (Hub Housing width) - 7/8ths Inch = 22.225mm
Bearing Tickness (Seating depth) - 9/32nds Inch = 7.14mm
Spacer Inner Diameter (Axle Thickness) - 9.525mm
Spacer Outer Diameter (Bearing Housing) - 13.525mm
Spacer Length (Space between Bearing) - 10mm
Weight: 101g
Please select which bearings you want
Please select which bearings you want
STREET CARVE Bearings BLACK x 8 STREET CARVE Bearings BLACK x 8
STREET CARVE Bearings RED x 8 STREET CARVE Bearings RED x 8
STREET CARVE Bearings WHITE x 8 STREET CARVE Bearings WHITE x 8
CERAMIC STREET CARVE Bearings WHITE x 8
Quantity required:
We have enough parts to make…  
RRP £20 - per set of 8 including spacers & O-Rings if applicable

RRP Includes 20% VAT

Non-EU customers purchase tax-free

Approx price :
To see UPS shipping rates you need to login.

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon