This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

GUMMIES Motormount & Axle Support kit - TWIN mounts

GUMMIES Motormount & Axle Support kit - TWIN mounts
RRP
£140
inc tax

Longboard & Skateboard Bearings (8 x 22 x 7mm) BLACK sidewalls with Black Logo ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

M5 x 10mm Countersunk Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M5 x 10mm COUNTERSUNK Bolt is made from A4 Marine Grade Stainless Steel & is used to secure the Spring into position on the Bottom of the Spring Truck hangers. The head of the Bolt is COUNTERSUNK so that it sits flush with your Hanger.

Using Marine Grade Stainless Steel, means these bolts will never rust on you! Weighing just 1.8g each, they are very lightweight, look very sexy & are totally non corrosive. They can cope with any terrain or weather. They laugh in the face of sandy/salty beaches & muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

You’ll need 2 of the TRAMPA M5 x 10mm Countersunk Bolts to construct 1 pair of TRAMPA Bindings. You’ll also need a 3mm Allen key to tighten & loosen the bolts. Don’t forget to make sure all you’re Nuts & Bolts are tight before you ride!

STREET Carver Truck Carbon Fiber Motor mounting panel made from 3k Twill Carbon Fibre 5mm Thick - GOOFY

Made from 3k Twill Carbon Fibre then Laser cut to precision, this Street Carver Motor Mount Carbon Fibre Panel is made specifically to fit the TRAMPA 118Kv & 136Kv Motors but will also fit many other Brand motors which are similar sized (6364) to the TRAMPA Motors. To Mount this LEFT foot forwards riding (REGULAR) Street Carver Carbon Motor Mount Panel to your Stret Carver Trucks you will need the Street Carver Truck Motor Mount connector, 2x very special ball ended Flat nosed M8x16mm Grub Srews which lock the Connector to the Hanger & 4x M5x16mm Countersunk Bolts to secure the Carbon Fiber panel to the motor mount connector.  The Street Carver Truck is basically the same as the Urban Carve Truck, the only difference being that the Hanger is facing the oposite direction in assembly. so its possible for your Carver Truck to be BOTH STREET CARVER & URBAN CARVER However if you then wish to add electric motors, you will need different kits for the different Street or Urban boards as the shape of the Hanger is different according to its direction of mount... QUESTION I'm also wondering, will the motors from Ollin Board Company fit on any of your motor mounts? ANSWER I guess the Olin motors will fit to our Motor Mounts no problem, but you will not gain the full benefits of our equipment as the motor axle shaft in the TRAMPA Motors is much longer & so our Mount makes the most of the bearing assisted motor axle support system which supports the axle shaft preventing bent axle shafts, belt slip & wear and tear. Generally the Axle Shaft Support system gives a much better performance all round as it holds the belt in the perfect position, but arguably yes your motors will attach to our Carbon Fibre motor mounts....

Motor Axle Support for Spring Truck Motor Mounts

This part ensures your motor is supported and the belt is running straight - two very important jobs for a smooth, fast and reliable board.

Motors with longer axles, like TRAMPA’s own, will fit perfectly into the housed bearing within, supporting the axle rotation, ensuring there is no ‘give’ in the axle, where the belt could potentially slip off at high speeds.

Fitting onto Channel Truck Motor Mounts this Motor Axle Support will work with any of the 6-9inch tyres in the TRAMPA range.

In this Kit you get the following parts -
Street Carve Truck Motor Mount Connector - T6 Aluminum
M8 x 16mm GRIPPY Grub Screw - Marine Grade Stainless Steel
M5 x 10mm Countersunk Bolt - Marine Grade Stainless steel
Street Carver Carbon Fibre Motor mounting Panel - GOOFY
TRAMPA ABEC 7 608 Longboard & skateboard Bearing - BLACK
Motor Axle Support for Spring Truck Motor Mounts
M4 x 16mm Socket Capped Bolt - Marine Grade Stainless Steel
Weight: 339g
Quantity required:
We have enough parts to make…  
RRP £140 - for the complete set

RRP Includes 20% VAT

Non-EU customers purchase tax-free

Approx price :
To see UPS shipping rates you need to login.

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon