TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.
TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.
TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.
As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.
& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.
M5 x 10mm Countersunk Bolt - Marine Grade Stainless steel with locking paste
Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!
Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.
The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..
Used For;
M4 x 40mm Socket Capped Bolt - Marine Grade Stainless steel with locking paste
TRAMPA's M4 x 40mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special Bolt is specifically made for TRAMPA & is used to assemble the TRAMPA SUPERSTAR HUBS. The socket capped head of the Bolt screws neatly though the Spokes & into the fixing point in the Rim of the SUPERSTAR HUB eventually screwing into the M4 nut on the other side easly.
Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!
Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.
Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!
Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.
M4 x 16mm Socket Capped Head TORX Bolt ISO 4762 Marine Grade Stainless Steel
TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush.
Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!
Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.
This is a 375mm long x 15mm wide High Torque Drive (HTD) Re-enforced Rubber Belt, which has 5mm Tooth Spacing (5M).
All of the Transmission Belts TRAMPA uses are a High Power (HP) rated. They are made by the world famous German company called STRONGBELT & thier belts are normally used for heavy industry applications.
We use this Strongbelt is used to transfer the power from the motor, through the Motor Pulley generating movement in the slave wheel of the TRAMPA ORRSOM Electric Longboards.
TRAMPA opted to set a new standard in E-Skating, becoming the first in the world to fit to all of the E-Boards in its range, a 15mm wide TRANSMISSON BELT as standard! Our standard 15mm belt is almost double the width of nearly all other E-Sk8's out there, they tend to use a flimsy off the shelf 8/9mm transmission belts which can be prone to stretch, slip & ultimately snap.
Using a re-enforced 15mm wide High Power Belt reduces stretch, eliminates slip & as a consequence provides a constantly smooth whilst incredibly intuitive power delivery direct to the rear Drive Wheels of your board. When accelerating or engine breaking (KERS), even from a standing start the STRONGBELT power is smooth & does not slip, or strain the motor, it does a damn gooood job!.....
STRONGBELT, as their name suggests, is a heavy industry brand that usually supplies the likes of Train manufacturers, where serious levels of quality with no excuses on failure are expected from the product as standard, as failure for such an item is serious as the consequences may result in death! STRONGBELT weave KEVLAR into their Pulley Belts, Kevlar is one of the strongest fibers known to man, its often added into materials to gain extra strength.... STRONGBELT have the best reputation in the Power Transmission Industry. These extra quality details in the production of our electronic motor drives, provides the maximum responsiveness achievable whilst maintaining a super smooth power delivery to the rider at all times.
Made from 3k Twill Carbon Fibre then Laser cut to precision, this Street Carver Motor Mount Carbon Fibre Panel is made specifically to fit the TRAMPA 118Kv & 136Kv Motors but will also fit many other Brand motors which are similar sized (6364) to the TRAMPA Motors. To Mount this LEFT foot forwards riding (REGULAR) Street Carver Carbon Motor Mount Panel to your Stret Carver Trucks you will need the Street Carver Truck Motor Mount connector, 2x very special ball ended Flat nosed M8x16mm Grub Srews which lock the Connector to the Hanger & 4x M5x16mm Countersunk Bolts to secure the Carbon Fiber panel to the motor mount connector. The Street Carver Truck is basically the same as the Urban Carve Truck, the only difference being that the Hanger is facing the oposite direction in assembly. so its possible for your Carver Truck to be BOTH STREET CARVER & URBAN CARVER However if you then wish to add electric motors, you will need different kits for the different Street or Urban boards as the shape of the Hanger is different according to its direction of mount... QUESTION I'm also wondering, will the motors from Ollin Board Company fit on any of your motor mounts? ANSWER I guess the Olin motors will fit to our Motor Mounts no problem, but you will not gain the full benefits of our equipment as the motor axle shaft in the TRAMPA Motors is much longer & so our Mount makes the most of the bearing assisted motor axle support system which supports the axle shaft preventing bent axle shafts, belt slip & wear and tear. Generally the Axle Shaft Support system gives a much better performance all round as it holds the belt in the perfect position, but arguably yes your motors will attach to our Carbon Fibre motor mounts....
Motor Axle Support for Spring Truck Motor Mounts
This part ensures your motor is supported and the belt is running straight - two very important jobs for a smooth, fast and reliable board.
Motors with longer axles, like TRAMPA’s own, will fit perfectly into the housed bearing within, supporting the axle rotation, ensuring there is no ‘give’ in the axle, where the belt could potentially slip off at high speeds.
Fitting onto Channel Truck Motor Mounts this Motor Axle Support will work with any of the 6-9inch tyres in the TRAMPA range.
TRAMPA's 14 Tooth Motor Pulley Wheel connects directly to the Motor Axle & is secured into position using a Magnetic Fixing Key & Locking Grub Screw.
This custom made Motor Pulley Wheel uses the German Made STRONGBELT which is 15mm wide and should never stretch or break on you whilst still providing the smoothest of power deliveries to the user even from a standing start....
Changing your Motor Pulley &/or Drive pulley wheels will drastically change the performance of your ride... :-)
TRAMPA's Motor Axle Shaft to Pulley KEYWAY measures 3 x 3 x 8mm. It connects into the Motor Pulley when mounted onto the motor Axle Shaft & is used to center the pulley on the Axle & to assist in delivering all the power from the motor without slip! This KEYWAY will fit to all TRAMPA motors amongst others.
TRAMPA's Axle length measures 38.5mm (from motor housing to end of shaft) & has a Diameter of 8mm. The centre of the key (3 x 3 x 8mm) sits 16.70mm away from the Motor front. Front side of Motor to Center of Key! Deduct 4mm & you have the length from front side of motor to the start of key....
44 Tooth Slave Pulley - Fits HYPA Wheels with Gummies Tyres
TRAMPA's 44 Tooth Slave Pulley has been designed to be used specifically when connecting electric motors through the URBAN Motor Mounts when using the new & oversized, super grippy GUMMIES longboard style tyres. The Gummies Tyres are due out very soon & available on advanced sale now! Frank was un-able to design 1 pulley to fit both styles of TRAMPA hub, so this one will only work with HYPA hubs specifically.
The 44 Tooth Slave Pulley has been precision milled from super-light-weight & mega strong Heat Treated T6 Aluminum. The pulleys teeth stand 5mm tall, this is the same size teeth as that found on TRAMPA's Premium 15mm wide German made 'Strongbelt' & when the Strongbelts are wrapped around the pulleys, the belt fits so efficiently it has what we call HIGH TORQUE DRIVE (HTD). HTD insures all of the motors Torque is pushed through the pulleys into the wheels & when coupled with the amazing VESC 6 & 12s Battery power provides instant smooth unreal Power on tap to the rider!
This smaller sized 44 Tooth pulley is actually higher in gearing than the 66 tooth & therefore when fitted it increases the final drive (top Speed) compensating for the smaller sized final drive the wheel was originally intended to fit to... Gummies tyres only measure 125mm which are obviously smaller than 6.5, 7 & 8 inch wheel options we also offer so the Gummies Tyres love the extra gearing the 44 Tooth Brings :-)
TRAMPA's 44 Tooth Slave Pulley for HYPA hubs works in conjunction with all & any of the 13, 14 or 15 tooth Motor Pulley in the range. Changing your Motor Pulley will drastically alter the performance & characteristics of your ride... 13 Tooth motor Pulley is best for Hill Climbing whilst 15 Tooth Motor Pulley is best for high speed, 14 tooth motor Pulley will give you good all round performance...
To connect the 44 Tooth Pulley to the HYPA hubs you will need 6x M4x40mm Socket capped Bolts which screw throurgh the HYPA wheel assembly directly into the Pulley very neatly!
Non-EU customers purchase tax-free
Approx price :