This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

Infinity Hanger - MAGURA Hydraulic Brakes with SOLID Disks to fit SUPERSTAR Wheels

TRAMPA's INFINITY HS11 MAGURA BRAKES / E-Drive HANGER is uses the strongest SPRING TRUCK Hanger in the TRAMPA product range! To ensure the maximum strength possible the hanger body is made from FORGED ALUMINUM & it is one solid piece! The INFINITY Hanger is fitted with 12mm SOLID STEEL Axles. The Solid Axles are HEAT TREATED. Heat treating steel makes it substantially stronger, more resistant to impact & less prone to rust. 12mm Solid Axles are without doubt the strongest Axles in the TRAMPA range. The Axles are first Glued & then Screwed with a Marine Grade Stainless Steel Grub Screw into the perfect position to mount your wheel.

Once the Hanger has had its Axles fitted it is sent away to the CNC factory to have the Kingpin holes & the Brake / E-Drive mounting points precision milled. CNC milling guarantees precision work. It is imperative that all of these important holes are accurately positioned in order to ensure the best performance to the rider, as well as making the Truck easy to assemble & service. The workers modify the back of the hanger by milling a flat surface so that we can mount the Brakes or E-Drive equipment flush against. We then drill an extra hole & insert it with a thread so to be able to screw in a bolt & fix something into it. A small semi-circle "Cradle" is milled at the top of the Hanger,  acting as an anchor, it eliminates movement normally associated to a single fixing point. We are able to fix the MAGURA Braking system or the NEW TRAMPA E-DRIVE system into this thread & cradle, making a very strong fix between the two. The HS11 Magura Braking System & the E-Drive system are both very powerful and they need a very strong mounting point for max performance.!

In order to give the "Two Tone Pimp Finish" the INFINITY Hanger is EDP painted MATT BLACK for metal protection & colour coordinating good looks before the CNC work is carried out. The INFINITY Brake Board / E-Drive Hanger measures 16 Inches in total width. When the wheels are fitted to the Hanger, the board has a "center wheel width" of 14 Inches.

Once back from the CNC factory, the MAGURA HS11 Hydraulic Brake calipers, loaded with "MAGURA ROYAL BLOOD" (Brake fluid) are then Screwed into this Hanger! It comes as a pre-assembled set, including SOLID BRAKE DISKS, SPACERS & specially made M 4x52.5mm Countersunk BOLTS ready to fit the Brake Disks directly to your SUPERSTAR Wheels. The Magura Brake system is very powerful. It can be fitted to the front or the back of the board to suit your riding preference. It can be squeezed gently to trim off top speed or it will stop you faster than you have ever imagined before! It has transformed the riding experience for many riders, opening up what was previously un-ridable terrain into easily conquerable terrain.

The HS11 Hydraulic Brake System is designed to fit the 35° HS11 Brake Deck or the 35° HolyPro Deck without any modification needed at all. The HS11 Truck will also fit to any 35° TRAMPA Deck, but as the calipers take up a lot of space on the hanger, some modifications may be needed to be made to the deck, in order to create the space to house them to allow the deck to steer correctly.

INFINITY Brake Hanger - 12mm SOLID Axles modifed to fit MAGURA Hydraulic brakes

TRAMPA's INFINITY HS11 MAGURA BRAKES / E-Drive HANGER is taken from the strongest SPRING TRUCK Hanger in the TRAMPA product range! To ensure the maximum strength possible the hanger body is made from FORGED ALUMINUM & is one solid piece! The INFINITY Hanger is fitted with 12mm SOLID STEEL Axles. The Solid Axles are HEAT TREATED. Heat treating steel makes it substantially stronger, more resistant to impact & less prone to rust. 12mm Solid Axles are without doubt the strongest Axles in the TRAMPA range. The Axles are first Glued & then Screwed with a Marine Grade Stainless Steel Grub Screw into the perfect position to mount your wheel.

Once the Hanger has had its Axles fitted it is sent away to the CNC factory to have the Kingpin holes & the Brake / E-Drive mounting points precision milled. CNC milling guarantees precision work. It is imperative that all of these important holes are accurately positioned in order to ensure the perfect assembly & best performance to the rider, as well as making the Truck easy to assembly & service. The workers modify the back of the hanger by milling a flat surface so that we can mount the Brakes or E-Drive equipment flush against. We then drill an extra hole & insert it with a thread to be able to screw a bolt to fix something into & a small semi-circle "Cradle" is milled at the top of the Hanger,  acting as an anchor, it eliminats movement normally associated to a single fixing point. We are able to fix the MAGURA Braking system or the NEW TRAMPA E-DRIVE system into this thread & cradle, making a very strong fix between the two. The HS11 Magura Braking System and the E-Drive Sytem are both very powerful, they need a very strong mounting point for max performance.!

In order to give the "Two Tone Pimp Finish" the INFINITY Hanger is EDP painted MATT BLACK for metal protection & colour coordinating good looks before the CNC work is carried out. The INFINITY Brake Board / E-Drive Hanger measures 16 Inches in total width. When the wheels are fitted to the Hanger, the board has a "center wheel width" of 14 Inches.

Magura Brake Calipers & Cables

Magura Hydraulic Brake kit. Including Handle, Cables, Connections, Mounting bracket & comes fully bled ready to be mounted.. This kit will only fit to a Trampa spring style hanger that has been modified to fit the brake system.. This kit will not fit to a regular Trampa Spring hanger.. You also need top purchase the mounting bolts and assembly spacers

Magura Bolt used to mount the calipers to the hanger - part A M6 x 12mm

Magura Brake special mounting bolt - used to fix the calipers to the hanger.. As expected from Trampa these parts are made from the finest A2 Marine Grade Stainless steel available to us & ensure a rust free connection for maximum durability!. Loosely place the calliper over bolt C & position part D into the half moon housing in the hanger.. Place part B (bolt mounting spacer) over bolts C & D and use part A to screw them both tightly into the hanger.. Using a 5mm Allen Key tighten the bolts into parts C+D into the hanger - you do not want any play in this part so make sure this is tight - FT!!

Magura Bolt mounting Spacer MG Stainless Steel - Part B

Magura mounting Bolt Spacer Marine Grade Stainless Steel - Part B. Secure your brake assembly through this special steel bracket.. As expected from Trampa this part is made from marine Grade Stainless Steel.. This special part gives the exact space required to fix parts C & D into the Hanger, FT!. Use part A to screw through part B into the fixing C & D into the Hanger. Ensure all the brake parts fixing to the hanger are very tight! FT!!

Magura Bolt used to mount the calipers to the hanger - part C

Magura Brake special mounting bolt, used to fix Calliper to Hanger. Part C is made from Marine Grade stainless steel and will not rust on you!. This part C screws into the modified hangers and Locks the calipers in position.. As a trick to fix this to the hanger, use an M6 bolt and 2 x M6 nuts to lock into the special part C and then tighten into the Hanger.. Using a 10mm spanner tighten this part into the hanger so its really tight - FT. The brake caliper sits over Part C and with use of parts B, D & A locks the caliper into position ready for use.

Magura Bolt used to mount the calipers to the hanger - part D

Magura Brake special mounting bolt - used to help fix the Calliper into hanger. Part D is made from Marine Grade Stainless steel and will never rust on you.. Once part C is anchored into the hanger, slip the calliper over part C and push this part D into position.. Part D will sit in the half moon that has been CNC'd into the hanger.. Once part D is in position, place the bolt spacer (part B) over the parts C & D and insert the screw (part A) into C & D. You may need to rest your finger at the back of part D in order to get a purchase when screwing in part A but as soon as this has some resistance it will tighten nicely. Ensure the connection between the callipers and the hangers is very tight! FT

Brake disk support spacer - fits between the spoke and the disk - part E

BRAKE DISK SUPPORT DISK - This little spacer fits perfectly between the spoke and the brake disk. It gives the perfect space to avoid over heating the tyre & to allow good ventilation to keep your brake system cool and effective.

These spacers can be purchased as sets in brake accessories or or if you have lost one singular here in parts.

Inner Diameter  = 4.5mm
Outer Diameter = 10mm
Spacer  Length  = 10mm 

Magura 90 Bango cable connector - part F

This special part allows us to make the modification from Bike brakes to Mountainboard Brakes.. The length of the cable required to fit the distance between your callipers is 265mm. Use a cable steady and clamp or vise to hold the brake cable tight, then tap in this Part F into the cable with hammer.. Be careful not to split the cable when tapping in. Do not over heat the cable as this makes it flexi when tapping in...

Magura Valve bolt - part G

Use this part G to fix through part F (the 90º pipe connector) and connect into the brake caliper.. This special screw is hollow with a hole and allows the blood to flow through the system.. Ensure you have copper washers (part H) either side of the Part F to ensure a water tight fit.. Make sure this part is screwed into the caliper tight, but do not over tighten as it is fragile & will snap!.. We are checking the Magura website for details of its exact tightness in newton meters...

Magura connecting copper Washer - part H

Use These copper washers (Part H) to fit between parts F & G when fixing into the calipers.. Use 1 washer on each side of the 90º connector. (Part F). So put 1 washer on part H, push through part G, and then add another washer before inserting into the caliper. Use a 5mm Alen Key to tighten, ensure its tight but do not over tighten!! be careful!

Magura Bleed Bung in Caliper - part I

This Bung (Part I) Screws into the Calipers and keeps the brake system Water tight.. Remove Part I to bleed your Brake system.. Part J needs to be pushed into a pipe and the pipe needs to be fitted to a syringe.. Then screw Part J into the Bung Housing.. Undo the bleed valve on the Brake lever and in the same way Fit part K into another pipe and when it has been loaded with fluid fix into the handle.. Push and pull the blood through the system until there is no air in and then remove the pipe connected to the handle & replace the small bung to water tight.. Remove the the other pipe and replace the Bung into the caliper, then test by squeezing the lever and ensure the system is water tight.. Purchase a service kit if you wish to bleed your equipment as this contains everything you will need to make the work nice and easy or make your own from parts you may have kicking around in the bike shed... You will find the Magura brake parts available in most good Bicycle shops on Ebay or here on our website

Magura Cable connector Wide - part J

This part will connect the cable from the calliper into the Handle. Place the cable into the cable holder and using a hammer gently tap in the pointed end into the cable. You can find a cable holder in the Magura service kit but is sadly not available as a separate item to purchasePurchase a service kit if you wish to bleed your equipment as this contains everything you will need to make the work nice and easy or make your own from parts you may have kicking around... You will find our Magura brake parts available in most good Bicycle shops.

Magura Banjo Cable connector Narrow - part K

Magura Banjo Cable connector Narrow fixes Bleed cable to Handle lever.. Place the cable into the cable holder and using a hammer gently tap in the pointed end into the cable. You can find a cable holder in the Magura service kit but is sadly not available as a separate item to purchase. This part is to be tapped into your bleed cable and then screwed into the Lever.. Purchase a service kit if you wish to bleed your equipment as this contains everything you will need to make the work nice and easy or make your own from parts you may have kicking around... You will find our Magura brake parts available in most good Bicycle shops.

Solid Brake disk to fit SUPERSTAR Hubs - Part L

TRAMPA's SOLID BRAKE DISKS give MAXIMUM PERFORMANCE! The Disks are skillfully made from 5mm Thick, Premium Quality Aluminum using the latest in high tech cutting equipment. When the brakes are in operation (slowing you down) the friction from the pads, pressing against the Aluminum disks generates heat. The extra thickness of the Aluminum we use, disperse's the heat faster, ensuring cooler operating temperatures, reducing potential brake fade during prolonged use whilst maximising performance to the rider at all times...

The TRAMPA Brake disks only fit to the TRAMPA SUPERSTAR Wheels. Special sized M4 x 52.5mm Countersunk Bolts and M4 x 10mm Aluminum spacers position the SOLID DISK in the perfect location far enough from the wheel allowing constant cooling at all times. Constant cooling to your disks reduces pad wear whilst maintaining maximum performance to your very powerful MAGURA brake system, allowing more control at top end roll speeds to the rider! These TRAMPA Brake disks are only to be used in conjunction with the TRAMPA SUPERSTAR wheel & the specially adapted MAGURA hydraulic brake kit. Be very careful during use & DO NOT TOUCH the disks when they have been operated as they will be very hot & will burn you! Shaped for appearance but designed for performance!

 

M4 x 52.5mm countersunk bolt - Marine Grade Stainless steel Brake disk to hub bolt

This bolt is the exact size fit for fixing the Disk brakes to Superstar Wheels. Its made from A2 Marine Grade Stainless steel & will never rust on you! Countersunk for flush neat fit into the disk - no protruding parts. Use a 2.5mm Allen Key to locate the bolt into the nut & use a 7mm spanner to tighten the nuts onto the bolts. Always try to tighten the nut onto the bolt and not the bolt into the nut & always ensure all nuts and bolts are tight before riding.

Bolt width = 4mm
Bolt length = 52.5mm

M4 Nut - Marine Grade stainless steel Nylock Nut - Hub Nuts #75

Introducing TRAMPA's M4 (4mm Shaft) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M4 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to tighten to the M4 Socket Capped Bolts that hold the HYPA & SUPERSTAR hubs together. To fit the nuts M4 use an 8mm spanner or  8mm Ratchet Socket to turn the Nut onto the Bolt whilst holding the bolt with a 3mm Allen Key. Always ensure your Nuts & Bolts are tight before you ride!

TRAMPA's INFINITY HS11 MAGURA BRAKES / E-Drive HANGER is taken from the strongest SPRING TRUCK Hanger in the TRAMPA product range! To ensure the maximum strength possible the hanger body is made from FORGED ALUMINUM & is one solid piece! The INFINITY Hanger is fitted with 12mm SOLID STEEL Axles. The Solid Axles are HEAT TREATED. Heat treating steel makes it substantially stronger, more resistant to impact & less prone to rust. 12mm Solid Axles are without doubt the strongest Axles in the TRAMPA range. The Axles are first Glued & then Screwed with a Marine Grade Stainless Steel Grub Screw into the perfect position to mount your wheel.

Once the Hanger has had its Axles fitted it is sent away to the CNC factory to have the Kingpin holes & the Brake / E-Drive mounting points precision milled. CNC milling guarantees precision work. It is imperative that all of these important holes are accurately positioned in order to ensure the best performance to the rider, as well as making the Truck easy to assemble & service. The workers modify the back of the hanger by milling a flat surface so that we can mount the Brakes or E-Drive equipment flush against. We then drill an extra hole & insert it with a thread to be able to screw a bolt to fix something into & a small semi-circle "Cradle" is milled at the top of the Hanger,  acting as an anchor, it eliminates movement normally associated to a single fixing point. We are able to fix the MAGURA Braking system or the NEW TRAMPA E-DRIVE system into this thread & cradle, making a very strong fix between the two. The HS11 Magura Braking System and the E-Drive system are both very powerful, they need a very strong mounting point for max performance.!

In order to give the "Two Tone Pimp Finish" the INFINITY Hanger is EDP painted MATT BLACK for surface protection & colour coordinating good looks before the CNC work is carried out.

The INFINITY Brake Board / E-Drive Hanger measures 16 Inches in total width. When the wheels are fitted to the Hanger, the board has a "center wheel width" of 14 Inches.

Once back from the CNC factory the Magura HS11 Hydraulic Brake calipers, loaded with "MAGURA ROYAL BLOOD" (Brake fluid) are fitted into the Hanger! It comes as a pre-assembled set, including VENTED BRAKE DISKS, SPACERS & specially made M4 x 52.5mm Countersunk BOLTS ready to fit the Brake Disks directly to your SUPERSTAR Wheels. The Magura Brake system is very powerful. It can be fitted to the front or the back of the board to suit your riding preference, the brakes can be squeezed gently to trim off top speed or it will stop you faster than you have ever imagined before! It has transformed the riding experience for many riders, opening up what was previously un-ridable terrain into easily conquerable terrain.

The HS11 Hydraulic Brake System is designed to fit the 35° HS11 Brake Deck or the 35° HolyPro Deck without any modification needed at all. The HS11 Truck will also fit to any 35° TRAMPA Deck, but as the calipers take up a lot of space on the hanger, some modifications may be needed to be made to the deck, in order to create the space to house them to allow the deck to steer correctly.

ATB INFINITY TRUCK
Super strong SOLID Forged Hanger - EDP Painted
12mm thick SOLID Steel Axles 16 Inches Wide
Fits to - 35º Decks
Weight: 1,230g



Quantity required:
RRP £185 - for the complete set

RRP Includes 20% VAT

Non-EU customers purchase tax-free

Approx price :
Approx. shipping price:

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon