TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.
TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.
TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.
As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.
& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.
TRAMPA's M5 x 10mm COUNTERSUNK Bolt is made from A4 Marine Grade Stainless Steel & is used to secure the Spring into position on the Bottom of the Spring Truck hangers. The head of the Bolt is COUNTERSUNK so that it sits flush with your Hanger.
Using Marine Grade Stainless Steel, means these bolts will never rust on you! Weighing just 1.8g each, they are very lightweight, look very sexy & are totally non corrosive. They can cope with any terrain or weather. They laugh in the face of sandy/salty beaches & muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.
You’ll need 2 of the TRAMPA M5 x 10mm Countersunk Bolts to construct 1 pair of TRAMPA Bindings. You’ll also need a 3mm Allen key to tighten & loosen the bolts. Don’t forget to make sure all you’re Nuts & Bolts are tight before you ride!
TRAMPA's M4 x 40mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special TRAMPA Bolt is used to assemble the TRAMPA SUPERSTAR HUBS. Using a 3mm Allen Key the Socket Capped head of the Bolt screws neatly though the SPOKES, through the fixing point in the Rim of the Hub, passing through the spoke on the other side and eventually screwing into the M4 nut on the other side easly.
Weighing just 3 grams each these bolts are very lightweight. They look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.
You will need a 3mm Allen Key to tighten & loosen the Nuts & Bolts from the hub. Ensure all your Nuts & Bolts are tight before riding!
This is a 330mm long x 15mm wide High Torque Drive (HTD) Re-enforced Rubber Belt, which has 5mm Tooth Spacing (5M). It is a High Power rated (HP) TRANSMISSON BELT made by the world famous German Brand called STRONGBELT. This one is used to transfer the power from the Motor & Motor Pulley into power at the rear wheels of a TRAMPA Electric Street Carver
TRAMPA opted to set a new standard in E-Skating, becoming the first in the world to fit to all of its E-Boards in its range a 15mm wide TRANSMISSION BELT. Our standard 15mm belt is almost double the width of nearly all other E-Sk8's out there, they tend to use a flimsy off the shelf 9mm transmission belt which can be prone to stretch, slip & ultimately snap. Using a re-enforced 15mm wide High Power Belt reduces stretch, eliminates slip & as a consequence provides a constantly smooth whilst incredibly intuitive power delivery direct to the rear Drive Wheels of your board. When accelerating or engine breaking (KERS), even from a standing start the STRONGBELT power remains smooth & does not slip, or strain the motor, it does a damn gooood job!.....
STRONGBELT, as their name suggests, is a Heavy Industry Brand that usually supplies the likes of Train manufacturers where serious levels of quality with no excuses on failure are expected from the product, as failure for such an item is serious & may result in death! STRONGBELT weave KEVLAR into their Pulley Belts, Kevlar is one of the strongest fibers known to man, its often added into materials to gain extra strength.... STRONGBELT have the best reputation in the Power Transmission Industry for NO stretching or snapping & we have high expectations from this quality item.
These extra quality details in the production of our electronic motor drives, provides the maximum responsiveness achievable whilst maintaining a super smooth power delivery to the rider at all times.
Made from 3k Twill Carbon Fibre then Laser cut to precision, this Street Carver Motor Mount Carbon Fibre Panel is made specifically to fit the TRAMPA 118Kv & 136Kv Motors but will also fit many other Brand motors which are similar sized (6364) to the TRAMPA Motors. To Mount this LEFT foot forwards riding (REGULAR) Street Carver Carbon Motor Mount Panel to your Stret Carver Trucks you will need the Street Carver Truck Motor Mount connector, 2x very special ball ended Flat nosed M8x16mm Grub Srews which lock the Connector to the Hanger & 4x M5x16mm Countersunk Bolts to secure the Carbon Fiber panel to the motor mount connector. The Street Carver Truck is basically the same as the Urban Carve Truck, the only difference being that the Hanger is facing the oposite direction in assembly. so its possible for your Carver Truck to be BOTH STREET CARVER & URBAN CARVER However if you then wish to add electric motors, you will need different kits for the different Street or Urban boards as the shape of the Hanger is different according to its direction of mount... QUESTION I'm also wondering, will the motors from Ollin Board Company fit on any of your motor mounts? ANSWER I guess the Olin motors will fit to our Motor Mounts no problem, but you will not gain the full benefits of our equipment as the motor axle shaft in the TRAMPA Motors is much longer & so our Mount makes the most of the bearing assisted motor axle support system which supports the axle shaft preventing bent axle shafts, belt slip & wear and tear. Generally the Axle Shaft Support system gives a much better performance all round as it holds the belt in the perfect position, but arguably yes your motors will attach to our Carbon Fibre motor mounts....
This part ensures your motor is supported and the belt is running straight - two very important jobs for a smooth, fast and reliable board.
Motors with longer axles, like TRAMPA’s own, will fit perfectly into the housed bearing within, supporting the axle rotation, ensuring there is no ‘give’ in the axle, where the belt could potentially slip off at high speeds.
Fitting onto Channel Truck Motor Mounts this Motor Axle Support will work with any of the 6-9inch tyres in the TRAMPA range.
TRAMPA's 14 Tooth Motor Pulley Wheel connects directly to the Motor Axle & is secured into position using a Magnetic Fixing Key & Locking Grub Screw.
This custom made Motor Pulley Wheel uses the German Made STRONGBELT which is 15mm wide and should never stretch or break on you whilst still providing the smoothest of power deliveries to the user even from a standing start....
Changing your Motor Pulley &/or Drive pulley wheels will drastically change the performance of your ride... :-)
TRAMPA's Motor Axle Shaft to Pulley KEYWAY measures 3 x 3 x 8mm. It connects into the Motor Pulley when mounted onto the motor Axle Shaft & is used to center the pulley on the Axle & to assist in delivering all the power from the motor without slip! This KEYWAY will fit to all TRAMPA motors amongst others.
TRAMPA's Axle length measures 38.5mm (from motor housing to end of shaft) & has a Diameter of 8mm. The centre of the key (3 x 3 x 8mm) sits 16.70mm away from the Motor front. Front side of Motor to Center of Key! Deduct 4mm & you have the length from front side of motor to the start of key....
TRAMPA's 33 Tooth Slave Wheel connects into all of TRAMPA's 83mm & 90mm Longboard Wheels perfectly! It connects through the Longboard Wheel using an Aluminum Centering Ring & M4 x 40mm Bolts with M4 M4 Nylock Nuts to lock it into position.
This custom made Slave Wheel can accept any size belt up to 17mm. TRAMPA uses's a German made 15mm wide STRONGBELT which provides a very smooth power delivery to the user, even from a standing start....
Changing your Motor Pulley &/or Slave pulley wheels will drastically change the performance characteristics of your ride... Small Pulleys at the Wheel Slows accelleration but increase's top the speed! :-)
With the use of 6x Marine Grade Stainless Steel M4x40mm Socket Capped Bolts & 6x M4 Nylock Nuts, TRAMPA's Longboard Wheel Slave Wheel CENTERING RING, which is made from Solid Aluminum, connects through & around the spokes of the 83 or 90mm Longboard Wheels, locking the Slave Wheel solid in position into the wheel & ready to be connected to the HTD (High Torque Drive) Rubber STRONGBELT to give for some super smooth, high speed electric motor action!
TRAMPA's STREET CARVER DRIVE TRAIN (SCDT) brings a complete new sensation to riding. Arguably the Mini Spring Trucks are a too wide for Old-Skool conventional Longboarders who still wish to push, we have herd them complaining about the wheel is in the way when they push and the steering is too loose for them, you have to remember the Street Carver was originally designed for steep down hill street runs where 'switch back carving' is required not pushing... BUT assemble it with either a Single or dare i suggest the insane Twin motor setup & Hey! you don't need to push any more!
& WOW! - Fitting a motor to your TRAMPA Street carve deck completely & utterly transforms any previous riding experience you may have ever experienced before! The resulting E-Street Carver Decks are like nothing thats ever been made before. We know they are expensive but it is genuinly utterly amazing & a totally revolutionary sensation which should not ever be compared to a traditional Longboard...
The STREET & URBAN CARVE DECKS are very much the same... the only difference between the complete decks are the wheels & Slave Pulleys used & to make the change between the two decks in particular the Hanger is assembled in a different direction relevant to the size of the wheel... The Axle in the Hanger is 'off set' so turning it around forwards or backwards changes the wheel base accordingly. Hanger facing inwards gives shorter deck & is for Street Carving requiring smaller longboard style wheels, Whilst hanger facing forwards give Longer Wheelbase for URBAN Carving as the extra size for space accommodates the larger wheels...
Non-EU customers purchase tax-free
Approx price :