This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

T Bar Scooter with Hi Tensile Forks

T-Bar 42CrMo4 Chromo Steel Scooter Handle Bars

Classic T-Bar Handlebars - OVERSIZED!! 4130 Chromo Steel - Heat Treated 580mm Tall x 580mm Wide with NO RAKE or RISE The DOWN-TUBE is Internally Fluted whilst the CROSSBAR is Externally Fluted Powdercoated Gloss Black for best surface finish.

400mm Hand made TRAMPA Vinyl Sticker - RED

Everybody loves stickers, especially TRAMPA VINYL stickers! TRAMPA vinyl's are pain-stakingly Hand Made at the TRAMPA HQ using the absolute finest Vinyl material available! So long as the area it is to be stuck to is clean the Vinyl we use is guaranteed to stick well & not fade for well over 5 years and most likely much longer! These RED Vinyl Stickers are sized to fit underneath the TRAMPA deck, the dimensions are 370mm long x 70mm high.

There are loads of colours to choose from & the price starts at just £2.50 each - so custom pimping your deck, car, van, boat, bedroom window or any other surface you can think of that would benefit with a TRAMPA logo slapped on it is really easy & cheap and easy to do...

Help TRAMPA the world with the Pimp-est vinyl stickers EVER! To Apply the Stickers - Ensure the surface you re applying too is clean & grease free before applying the sticker. Peel the thick side away from the Masking tape so the sticker appears in reverse (negative) and simply lay the masking tape onto the surface in question. Using your fingers or a soft cloth, rub the masking tape, forcing any air out of the vinyl & allowing the vinyl to stick well. Then gently peel away the masking tape to reveal the Vinly.

8mm NICKLE PLATED Kingpin

This M8 x 80mm Nikel Plated Spring Truck Kingpin is used to connect the Hanger & the Baseplate on the TRAMPA INFINITY, VERTIGO or ULTIMATE Trucks. By using an 8mm Kingpin we have managed to save loads of weight whilst retaining all the strength necessary for the job by using high quality metals true to our word!

This M8 x 80mm Kingpin connects through the truck & into an M6 Nut. You'll need a 4mm Allen key to hold the Kingpin & a 10mm spanner to tighten/loosen your M6 Kingpin Nut.

This Kingpin pushes through plastic bushings before being placed into position in the Truck System. The Plastic bushings allow the metal parts (Hanger & Baseplate) to move inside each other without allowing the metal parts to touch or wear out. The plastic bushings will wear out over time and use and will eventually perish and need replacing. SO, make sure your Bushings are always in good working order after riding riding or when upgrading your Kingpin, it might be time to replace them too due to the unavoidable wear and tear of moving mountainboard parts.

This Kingpin lives up to TRAMPA's incredibly high quality standards, but it's always handy to have a spare just in case you do break one out on a ride.... Upgrade ur Kingpin by fitting the TRAMPA TITANIUM Kingpin which will save you loads of weight & fit into all of the TRAMPA Spring Trucks.

M5 x 8mm Countersunk Bolt - Marine Grade Stainless steel with locking paste

This M5 x 8mm COUNTERSUNK Bolt is made from A4 Marine Grade Stainless Steel & is used to secure TRAMPA RATCHET BUCKLES or tthe TRAMPA CAMLOCK BUCKLES onto the TRAMPA FOOTSTRAPS. The head of the Bolt is COUNTERSUNK so that it sits flush with your binding buckle.

Using Marine Grade Stainless Steel, means these bolts will never rust on you! Weighing just 1.8g each, they are very lightweight, look very sexy & are totally non corrosive. They can cope with any terrain or weather. They laugh in the face of sandy/salty beaches & muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

You’ll need 2 of the TRAMPA M5 x 8mm Countersunk Bolts to construct 1 pair of TRAMPA Bindings. You’ll also need a 3mm Allen key to tighten & loosen the bolts. Don’t forget to make sure all you’re Nuts & Bolts are tight before you ride!

8 Inch Regular Inner Tube made by PRIMO - 200x50mm

PRIMO's own 8 Inch Inner Tube has dimensions of 200mm (outer diameter) x 50mm (width) & will fit into all known 8 inch Tyres & ATB hubs on the market!

The CST PRIMO Inner Tube incorporates slightly thicker rubber into its manufacture process which means the tube is slightly heavier than alternatives but does allow the rider to inflate slightly higherThis extra thickness also gives some extra resistance to punctures, but punctures suck, so always carry a spare inner tube when you are riding as you never know when you might get one.  

The PRIMO Tube uses a 90º Brass Inflation valve which will not rust on you & comes as you would expected with a plastic "anti dust" valve cap!

8mm NICKLE PLATED Kingpin

This M8 x 80mm Nikel Plated Spring Truck Kingpin is used to connect the Hanger & the Baseplate on the TRAMPA INFINITY, VERTIGO or ULTIMATE Trucks. By using an 8mm Kingpin we have managed to save loads of weight whilst retaining all the strength necessary for the job by using high quality metals true to our word!

This M8 x 80mm Kingpin connects through the truck & into an M6 Nut. You'll need a 4mm Allen key to hold the Kingpin & a 10mm spanner to tighten/loosen your M6 Kingpin Nut.

This Kingpin pushes through plastic bushings before being placed into position in the Truck System. The Plastic bushings allow the metal parts (Hanger & Baseplate) to move inside each other without allowing the metal parts to touch or wear out. The plastic bushings will wear out over time and use and will eventually perish and need replacing. SO, make sure your Bushings are always in good working order after riding riding or when upgrading your Kingpin, it might be time to replace them too due to the unavoidable wear and tear of moving mountainboard parts.

This Kingpin lives up to TRAMPA's incredibly high quality standards, but it's always handy to have a spare just in case you do break one out on a ride.... Upgrade ur Kingpin by fitting the TRAMPA TITANIUM Kingpin which will save you loads of weight & fit into all of the TRAMPA Spring Trucks.

PRIMO ALPHA Lite - BLACK 8 Inch Tyre

The PRIMO ALPHA Lite tyre is a super light-weight Off-Road Tyre. Using just 2 PR of the finest grade rubber & incorporating a very high TPI under its skin combined together these secret details reduce weight considerably, making its reputation as the worlds best Off Road 8-inch Tyre! When inflated the PRIMO ALPHA Lite tyre measures 200x50mm. The Tyre incorporates a 3.75 inch Steel Band into the rim to hold everything in position & it slips onto the TRAMPA hubs perfectly. The ALPHA tyre will fit to all known hub Brands that are used for Mountainboarding & Kiteboarding. 

Made from relatively softish rubber the ALPHA tyre gives fantastic grip. Its design incorporates a wide center bead to allow & maintain straight line speed, whist its surrounding edges are beautifully sculptured wide grooves that supply high levels of grip regardless of the terrain type. - This tyre really is great for all off road applications.

The more you inflate your Tyres the faster you will roll!  The official maximum inflation pressure set by the factory for the ALPHA Tyre is 50psi, but the ALPHA Tyres are made so well & the TRAMPA Hubs are so strong that our Crash test Dummies (I mean Team Riders) have been known to inflate these Tyres well beyond their recommended pressures with no problems to mention. Over inflating your tyres may lead to an explosion which could seriously injure you. If you do decide to go beyond the max inflation pressure ensure your nuts & bolts are tight & deflate back to a regular pressure after use.

All Terrain Board Bearings (12 x 28 x 8mm) BLACK sidewalls with Embossed Logo ABEC 5 6001 2RS

TRAMPA's own ABEC 7 STAINLESS STEEL Mountain / Kite-board bearings measure 12 x 28 x 8mm & will fit to 12mm axles. They are officially known as s6001 RS Bearings. s Stands for Stainless Steel whilst 6001 tells you the bearings size & RS means the bearing has Rubber Seals. The Rubber Seals are inserted into the Outer raceway and in contact with the inner raceway, protecting the lubricated ball bearings from the ingress of moisture, dust & dirt, retaining the pre-filled grease within the bearing & maintaining maxium performance to the board & rider for as long as possible. The Stainless steel bearings only come in BLACK!

These precision made TRAMPA Bearings are polished to an internationally recognised ABEC 7 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 7 polishing gives you a super smooth / super fast ride which prolonges top end roll speeds. Using Bearing Reducer Spacers you are able to make these Bearings fit to 9.52mm Skate Truck Axles or 10mm Scooter Axles no problem....

Axle Kingpin mounting bushings for TRAMPA Scooter

1mm Base Kingpin bushings for Spring Trucks. These bushings are housed within the Baseplate and Hanger. They allow the kingpin to move freely when the Truck is constructed. Made with different thickness base's to avoid any tolerance issues in production. Produced from the highest standard plastics available to ensure maximum Durabillity & to enable the best maximum performance in your Trucks. Check & replace these bushings from time to time to ensure your steering stays in top condition.    

All Terrain Board Bearings (12 x 28 x 8mm) BLACK sidewalls with Embossed Logo ABEC 5 6001 2RS

TRAMPA's own ABEC 7 STAINLESS STEEL Mountain / Kite-board bearings measure 12 x 28 x 8mm & will fit to 12mm axles. They are officially known as s6001 RS Bearings. s Stands for Stainless Steel whilst 6001 tells you the bearings size & RS means the bearing has Rubber Seals. The Rubber Seals are inserted into the Outer raceway and in contact with the inner raceway, protecting the lubricated ball bearings from the ingress of moisture, dust & dirt, retaining the pre-filled grease within the bearing & maintaining maxium performance to the board & rider for as long as possible. The Stainless steel bearings only come in BLACK!

These precision made TRAMPA Bearings are polished to an internationally recognised ABEC 7 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 7 polishing gives you a super smooth / super fast ride which prolonges top end roll speeds. Using Bearing Reducer Spacers you are able to make these Bearings fit to 9.52mm Skate Truck Axles or 10mm Scooter Axles no problem....

Rubber O-Ring to fit in Bearings - 2mm Section x 8mm Bore NITRILE 70

This O-Ring should be fitted when a 9.525 x 16.5mm Bearing Support Spacer is fitted into the wheel assembly when fitting a wheel onto 9.525mm Axles. It fits alongside the Bearing Support Spacer, in-between the Bearings. This O-Ring prevents rattles from the spacer against the bearings. Over time, during the usage of your board, the bearings & spacers are put under a lot of force. Ultimately this force has to go somewhere... The Bearings use a Steel ring in their assembly where as the Bearing Support Spacers are made from Aluminum. Steel is much stringer than Aluminum & when forced against each the aluminum will loose out every time! This is what happens to your spacers between the bearings, the Bearings put force onto your spacers as a consequence over time the spacers shrink... With enough time its possible for an annoying rattle to start.... That's when you fit these little O-Rings!! :-)

Rubber O-Ring to fit in Bearings - 2mm Section x 10mm Bore NITRILE 70

This O-Ring should be fitted when a 12 x 16.5mm Bearing Support Spacer is fitted into the wheel assembly when fitting a wheel onto 12mm Axles.

It fits alongside the Bearing Support Spacer, in-between the Bearings. This O-Ring prevents rattles from the spacer against the bearings. Over time, during the usage of your board, the bearings & spacers are put under a lot of force. Ultimately this force has to go somewhere... The Bearings use a Steel ring in their assembly where as the Bearing Support Spacers are made from Aluminum. Steel is much stronger than Aluminum & when forced against each the aluminum will loose out every time! This is what happens to your spacers between the bearings, the Bearings put force onto your spacers as a consequence over time the spacers shrink... With enough time its possible for an annoying rattle to start.... That's when you fit these little O-Rings!! :-)

Axle Kingpin mounting bushings for TRAMPA Scooter

1mm Base Kingpin bushings for Spring Trucks. These bushings are housed within the Baseplate and Hanger. They allow the kingpin to move freely when the Truck is constructed. Made with different thickness base's to avoid any tolerance issues in production. Produced from the highest standard plastics available to ensure maximum Durabillity & to enable the best maximum performance in your Trucks. Check & replace these bushings from time to time to ensure your steering stays in top condition.    

Shim spacer - STAINLESS STEEL - Bridges tiny gaps on axles - 9.525 x 13.525 x 1mm

This tiny STEEL Shim Spacer is precision made to give maximum performance! It is used to hold the bearings in the perfect position & also to bridge tiny gaps on the axles, ensuring an accurate fit with NO rattles!

The Shim spacer slips onto the axle fitting either side of the Bearings when the wheel is being fitted onto 9.525mm Axles.

This tiny spacer positions the wheel perfectly on the axle, holding the Bearing in the best possible place to help achieve maximum spin rate for the wheel. Its little parts like these that suffer the most amount of abuse, especially when they are used in the harsh conditions that they are. Check from time to time they are in good order & possibly replacing them every now & then this good proactice will ensure your board stays in tip-top condition, always!

Shim spacer - STAINLESS STEEL - Bridges tiny gaps on axles - 9.525 x 13.525 x 1mm

This tiny STEEL Shim Spacer is precision made to give maximum performance! It is used to hold the bearings in the perfect position & also to bridge tiny gaps on the axles, ensuring an accurate fit with NO rattles!

The Shim spacer slips onto the axle fitting either side of the Bearings when the wheel is being fitted onto 9.525mm Axles.

This tiny spacer positions the wheel perfectly on the axle, holding the Bearing in the best possible place to help achieve maximum spin rate for the wheel. Its little parts like these that suffer the most amount of abuse, especially when they are used in the harsh conditions that they are. Check from time to time they are in good order & possibly replacing them every now & then this good proactice will ensure your board stays in tip-top condition, always!

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

M4 x 35mm Socket Capped Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 35mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This Bolt is used to assemble the TRAMPA HYPA HUBS. The socket capped head of the Bolt fits neatly into the Bolt housing of the HYPA HUB marrying into the M4 nut located in the housing on the other side of the hub.

Weighing just 3 grams each these bolts are very lightweight. They look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

You will need a 3mm Allen Key to tighten & loosen the Nuts & Bolts from the hub. Ensure all your Nuts & Bolts are tight before riding!

M4 Nut - Marine Grade stainless steel Nylock Nut - Hub Nuts #75

Introducing TRAMPA's M4 (4mm Shaft) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M4 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to tighten to the M4 Socket Capped Bolts that hold the HYPA & SUPERSTAR hubs together. To fit the nuts M4 use an 8mm spanner or  8mm Ratchet Socket to turn the Nut onto the Bolt whilst holding the bolt with a 3mm Allen Key. Always ensure your Nuts & Bolts are tight before you ride!

Bearing support spacer - Hypa Hubs on 12mm axles - 12 x 16 x 18.2mm - HYPA

This special Spacer measures 12mm (id) x 16mm (od) x 18.2mm (long) & has 2 uses!. It is firstly known as the Bearing Support Spacer as this Spacer fits between the Bearings of a 6 Spoked HYPA Hub, (when mounting the HYPA wheel onto 12mm Axles) & secondly it is also known as the AXLE SUPPORT SPACER as this spacer is also used to position any of the TRAMPA wheels in the perfect position onto the axles of 12mm TRAMPA Spring trucks....

TRAMPA spacers are produced as one long tube. The Tube is Heat Treated to gain extra strength & is then Bead Polished to give the metal extra surface protection & a shiny best appearance. The tube is then cut to the exact length for precision mounting. 

The following are required to build this product:

 

As you would expect from TRAMPA every mm of our T-BAR Scooter has been produced using the highest quality best performing materials available, all of which have had the very latest in manufacturing techniques such as Extrusion, Internal Fluting, Internal Networking, Internal Butting & Heat Treatment, all of which have been precision CNC machined to very high tolerance requirements, so that when all the amazing components are assembled together the resulting product is mega lightweight (5kg) whilst incredibly strong, resulting in an exceptionally smooth Anti vibration/rattle construction which makes the scooter incredibly fast n very stylish ride for the user!

All of the TRAMPA Scooters are available with a choice of any Custom HYPA or SUPERSTAR hub & of course with a choice of any tyre! TRAMPA SCOOTERS can be used on any surface or environment from Skate parks to forest trails, Cycle Paths or even very conveniently ripping through the city for a spot of shopping & using the special Wheel assembly that TRAMPA has developed means it takes just 5 minutes to swap over the tyre's...

Component Weights

TRAMPA Scooter Frame - Extruded & T6 Heat Treated 6061 Aluminum precision welded then fine bead blasted for a quality textured surface with silver anodisation for surface protection - Amazing!2,050g
TRAMPA's amazing T Bar Handlebars - Internally Fluted Down Tube with Externaly Fluted Crossbarl Heat Treated & Black powdercoated made using the finest 42CrMo4 Chromo Steel1,005g
BMX Style Forks made using Heat treated 42CrMo4 Chromo Steel that's been internally networked & Butted & finally BLACK Powdercoated595g
Build your own Custom Hypa Wheel !842g
TRAMPA's HIC (Hidden Internal Compression) Fully Integrated Headset 192g
Mansize 180mm & Flangeless TRAMPA Bar Grips & QUALA T Bar Ends125g
Jessups Grip Tape Scooter Frame shaped40g
NICKLE PLATED Front Wheel Axle pin Assembly Kit 76g
NICKLE PLATED Rear Wheel Axle pin Assembly Kit 80g
3d Sprung Stainless Steel Brake Fender & Antivibration Mounting kit161g
3D QUALA T Scooter Frame Badge2g
400mm Hand made TRAMPA Vinyl Sticker - RED1g
Total component weight5,169g
Grips Height - 580cm
Bar Width - 580cm
Handle Bar Rake - 0º°
Weight: 5,169g
Do you want HYPA or SUPERSTAR Wheels on your Scooter??
Do you want HYPA or SUPERSTAR Wheels on your Scooter??
T-Bar Scooter with Hypa Wheels T-Bar Scooter with Hypa Wheels
T-Bar Scooter with Superstar Wheels T-Bar Scooter with Superstar Wheels
What colour Hypa hub would you like ?
What colour Hypa hub would you like ?
Matt Black Hypa hub Matt Black Hypa hub
Matt White Hypa hub Matt White Hypa hub
Army Camo Hypa hub (+£5) Army Camo Hypa hub (+£5)
Black Gloss Hypa hub (+£5) Black Gloss Hypa hub (+£5)
Blue with Black logo's Hypa hub (+£5) Blue with Black logo's Hypa hub (+£5)
Carbon Fiber Print Hypa hub (+£5) Carbon Fiber Print Hypa hub (+£5)
Red Gloss Black logo (+£5) Red Gloss Black logo (+£5)
White Gloss Black Logo (+£5) White Gloss Black Logo (+£5)
White Gloss Blue Logo (+£5) White Gloss Blue Logo (+£5)
White Gloss Red Logo (+£5) White Gloss Red Logo (+£5)
Winter Camo (+£5) Winter Camo (+£5)
Which Tyre & Tube combo would you like on your custom Wheel?
Which Tyre & Tube combo would you like on your custom Wheel?
8 Inch SOFT TRAMPA Treads Tyre & Innova Tube 8 Inch SOFT TRAMPA Treads Tyre & Innova Tube
8 Inch HARD TRAMPA Treads Tyre & Innova Tube 8 Inch HARD TRAMPA Treads Tyre & Innova Tube
8 Inch BLACK Innova INLINE Street Tyre & Tube 8 Inch BLACK Innova INLINE Street Tyre & Tube
8 Inch GREY Innova INLINE Street Tyre & Tube 8 Inch GREY Innova INLINE Street Tyre & Tube
8 Inch BLACK Primo ALPHA Tyre & Tube (+£5) 8 Inch BLACK Primo ALPHA Tyre & Tube (+£5)
8 Inch RED Primo ALPHA Tyre & Tube (+£5) 8 Inch RED Primo ALPHA Tyre & Tube (+£5)
8 Inch BLUE Primo ALPHA Tyre & Tube (+£5) 8 Inch BLUE Primo ALPHA Tyre & Tube (+£5)
8 Inch BLACK Primo STRIKER Tyre & Tube (+£5) 8 Inch BLACK Primo STRIKER Tyre & Tube (+£5)
8 Inch BLACK MUD-PLUGGER Tyre & Tube (+£5) 8 Inch BLACK MUD-PLUGGER Tyre & Tube (+£5)
8 Inch BLACK KK SLICK cut Tyre & Tube (+£5) - OUT OF STOCK 8 Inch BLACK KK SLICK cut Tyre & Tube (+£5) - OUT OF STOCK
8 Inch GREY KK SLICK cut Tyre & Tube (+£5) 8 Inch GREY KK SLICK cut Tyre & Tube (+£5)
Please select what colour Bearings you want with your wheels?
Please select what colour Bearings you want with your wheels?
BLACK 12mm ATB Bearings ABEC 5 6001 2RS BLACK 12mm ATB Bearings ABEC 5 6001 2RS
BLUE 12mm ATB Bearings ABEC 5 6001 2RS BLUE 12mm ATB Bearings ABEC 5 6001 2RS
RED 12mm ATB Bearings ABEC 5 6001 2RS RED 12mm ATB Bearings ABEC 5 6001 2RS
What colour stickers would you like ?
What colour stickers would you like ?
Silver TRAMPA Stickers Please Silver TRAMPA Stickers Please
Alpha Blue TRAMPA Stickers Please Alpha Blue TRAMPA Stickers Please
Alpha Red TRAMPA Stickers Please Alpha Red TRAMPA Stickers Please
White TRAMPA Stickers Please White TRAMPA Stickers Please
Bronze TRAMPA Stickers Please Bronze TRAMPA Stickers Please
Pimp Chrome TRAMPA Stickers Please(+£3) Pimp Chrome TRAMPA Stickers Please(+£3)
Quantity required:
RRP £350 - per Scooter

RRP Includes 20% VAT

Non-EU customers purchase tax-free

Approx price :
Approx. shipping price:

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon