This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

TRAMPA CERAMICS 608 Professional Skate Bearings (8 x 22 x 7mm) GREEN shields with BLACK Logo x 8

CERAMIC Longboard & Skateboard Bearings (8 x 22 x 7mm) GREEN Sidewalls with Black Logo 608

TRAMPA's CERAMIC 608 Bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's CERAMIC Bearings are the Highest Precision 608 2RS Skate Bearings in the TRAMPA Arsenal!! CERAMIC Bearings suffer less friction when turning, making them the fastest spinning bearings you can fit into your board. TRAMPA's Ceramic Bearings are the standard by which all other skate bearings on the market should measured against & have become the Professional Boarders Bearing of choice!

To ensure no corrosion the Ceramic Bearings are coated in a super fine grease similar to Speed Cream & then mounted into a Stainless Steel Raceway & finally to prevent the ingress of dirt are fitted with Non-contact (Frictionless) Removable Shields (2RS). Adding Removable Shields makes the bearings easy to clean & most importantly service. If serviced regular TRAMPA's Ceramic Bearings will last you a life time, well at least a long time & certainly much longer than if no service at all! :-)

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

QUESTION
I am contacting you, hoping to find out if any ceramic bearings will work with the electric street carver with ultimate trucks.

ANSWER
No bro, the ceramic bearings will not fit to the street or Urban carver sized axles... the axle metric size is 9.525mm ( but really they are imperial size 3/8ths of an inch) where as the ceramics are metric 8mm exactly...

8 x 12 x 10.3mm Carbon Steel Internal Bearing Support Longboard wheel bearings Spacer

This spacer will fit onto an 8mm axle, it has a 12mm outer diameter & is 10.3mm Long in length. Its job is to fit between the bearings of longboard wheels to support the load through the bearing centre, its strongest point.

The Carbon Steel Longboard wheel Spacer is .3mm oversized to allow for shrinkage gained from natural usage over time which ultimately prevents ratttle & maintains best performance to the user for as long as possible. From time to time it is good practice for you to exchange your spacers to ensure maximum performance at all times.

TRAMPA's CERAMIC 608 Bearings are supplied with Internal Bearing Support Spacers & will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's CERAMIC Bearings are the Highest Precision 608 2RS Skate Bearings in the TRAMPA Arsenal!! CERAMIC Bearings suffer less friction when turning, making them the fastest spinning bearings you can fit into your board. TRAMPA's Ceramic Bearings are the standard by which all other skate bearings on the market should measured against & have become the Professional Boarders Bearing of choice!

To ensure no corrosion the Ceramic Bearings are coated in a super fine grease similar to Speed Cream & then mounted into a Stainless Steel Raceway & finally to prevent the ingress of dirt are fitted with Non-contact (Frictionless) Removable Shields (2RS). Adding Removable Shields makes the bearings easy to clean & most importantly service. If serviced regular TRAMPA's Ceramic Bearings will last you a life time, well at least a long time & certainly much longer than if no service at all! :-)

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

TRAMPA's Longboard bearing sets are supplied with 10.18mm Bearing Support Spacers. The spacer job is to fit between the bearings of the longboard wheels to support the loads gained through the center of the bearing centre which is its strongest point. The Carbon Steel Longboard wheel Spacer is 0.18mm oversized to allow for shrinkage gained from natural usage over time. The spacer maintains best performance to the user for as long as possible. From time to time it is good practice for you to exchange your spacers to ensure maximum performance at all times.

TRAMPA CERAMIC 608 Longboard & Skateboard Bearings - GREEN
Carbon Steel Longboard Wheel Internal Bearing Support Spacer
Bearing Inner Diameter (Axle thickness) - 8mm
Bearing Outer Diameter (Hub Housing width) - 22mm
Bearing Tickness (Seating depth) - 7mm
Spacer Inner Diameter (Axle Thickness) - 8mm
Spacer Outer Diameter (Bearing Housing) - 12mm
Spacer Length (Space between Bearing) - 10.3mm
Weight: 93g
Quantity required:
RRP £50 - per set

RRP Includes 20% VAT

Non-EU customers purchase tax-free

Approx price :
Approx. shipping price:

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon