This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

TRAMPA Longboard Bearing & Skateboard Bearing ABEC 7 8x22x7mm 608

Longboard & Skateboard Bearings (8 x 22 x 7mm) BLACK sidewalls with Black Logo ABEC 7 608

 

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

8 x 12 x 10.3mm Carbon Steel Internal Bearing Support Longboard wheel bearings Spacer

This spacer will fit onto an 8mm axle, it has a 12mm outer diameter & is 10.3mm Long in length. Its job is to fit between the bearings of longboard wheels to support the load through the bearing centre, its strongest point.

The Carbon Steel Longboard wheel Spacer is .3mm oversized to allow for shrinkage gained from natural usage over time which ultimately prevents ratttle & maintains best performance to the user for as long as possible. From time to time it is good practice for you to exchange your spacers to ensure maximum performance at all times.

TRAMPA's Longboard bearings are supplied with Internal Bearing Support Spacers & will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

TRAMPA's Longboard bearing sets are supplied with 10.18mm Bearing Support Spacers. The spacer job is to fit between the bearings of the longboard wheels to support the loads gained through the center of the bearing centre which is its strongest point. The Carbon Steel Longboard wheel Spacer is 0.18mm oversized to allow for shrinkage gained from natural usage over time. The spacer maintains best performance to the user for as long as possible. From time to time it is good practice for you to exchange your spacers to ensure maximum performance at all times.

TRAMPA ABEC 7 608 Longboard & skateboard Bearing - BLACK
Carbon Steel Longboard Wheel Internal Bearing Support Spacer
Bearing Inner Diameter (Axle thickness) - 8mm
Bearing Outer Diameter (Hub Housing width) - 22mm
Bearing Tickness (Seating depth) - 7mm
Spacer Inner Diameter (Axle Thickness) - 8.1mm
Spacer Outer Diameter (Bearing Housing) - 10.9mm
Spacer Length (Space between Bearing) - 10.3mm
Weight: 101g

Quantity required:
RRP £22.50 - per set

RRP Includes 20% VAT

Non-EU customers purchase tax-free

Approx price :
Approx. shipping price:

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon