This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

URBAN CARVE Motormount with Axle Shaft Support & 66 tooth Pulley kit - SINGLE

URBAN CARVE Motormount with Axle Shaft Support & 66 tooth Pulley kit - SINGLE URBAN CARVE Motormount with Axle Shaft Support & 66 tooth Pulley kit - SINGLE
RRP
£125
inc tax

Longboard & Skateboard Bearings (8 x 22 x 7mm) BLACK sidewalls with Black Logo ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

TORX M5 x 16mm Countersunk Bolt - Marine Grade Stainless steel with Fitting

TRAMPA's M5 x 16mm COUNTERSUNK Bolt is made from A4 Marine Grade Stainless Steel. 

The head of the Bolt is COUNTERSUNK. Countersinking the head of the bolt means that when it is screwed into position it sits flush  & neat with the surface it is screwed into, preventing items standing proud eliminating the chance of getting hung-up should it get caught on anything....

Weighing just 1.8g each, they are very lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.  

You’ll also need a 3mm Allen key to tighten & loosen the bolts. Don’t forget to make sure all you’re Nuts & Bolts are tight before you ride!

460 long x 15mm wide High Torque Drive (HTD) 5M (5mm Tooth Space) High Power (HP) STRONGBELT for TRAMPA Mountainboards

This ia 460mm long x 15mm wide High Torque Drive (HTD) Re-enforced Rubber Belt, which has 5mm Tooth Spacing (5M). This Belt is High Power rated (HP) & arguably over engineered for our application as the belt is made in Germany by the world famous company called STRONGBELT, who usually supply into heavy industry public sector applications which demand much more stringent requirements of any electric skateboard! This belt is used to transfer the power from the Motor & Motor Pulley into power at the rear wheels of a TRAMPA Electric Mountainboard.

TRAMPA opted to set a new standard in E-Skating, becoming the first in the world to fit to all of its E-Boards, a 15mm wide TRANSMISSON BELT. Our standard 15mm belt is almost double the width of nearly all other E-Sk8's out there, they tend to use a flimsy off the shelf 9mm transmission belt which are prone to stretch, slip & ultimately snap. Using a re-enforced 15mm wide High Power Belt reduces stretch, eliminates slip & as a consequence provides a constantly smooth whilst incredibly intuitive power delivery direct to the rear Drive Wheels of your board. When accelerating or engine breaking (KERS), even from a standing start the STRONGBELT power is smooth & does not slip, or strain the motor, it does a damn gooood job!.....

STRONGBELT, as their name suggests, is a Heavy Industry German Brand that usually supplies the likes of Train manufacturers where serious levels of quality with no excuses on failure are expected from the product, as failure for such an item is serious & may result in death! STRONGBELT weave KEVLAR into their Pulley Belts, Kevlar is one of the strongest fibers known to man, its often added into materials to gain extra strength.... STRONGBELT have the best reputation in the Power Transmission Industry for NO stretching or snapping & we have high expectations from this quality item. 

These extra quality details in the production of our electronic motor drives, provides the maximum responsiveness achievable whilst maintaining a super smooth power delivery to the rider at all times. 

Motor Axle Support for Spring Truck Motor Mounts

This part ensures your motor is supported and the belt is running straight - two very important jobs for a smooth, fast and reliable board.

Motors with longer axles, like TRAMPA’s own, will fit perfectly into the housed bearing within, supporting the axle rotation, ensuring there is no ‘give’ in the axle, where the belt could potentially slip off at high speeds.

Fitting onto Channel Truck Motor Mounts this Motor Axle Support will work with any of the 6-9inch tyres in the TRAMPA range.

14 Tooth Aluminum Motor Pulley with 5mm Deep teeth High Torque Drive (HTD) Fits 15mm Belts onto 8mm Motor Axles

TRAMPA's 14 Tooth Motor Pulley Wheel connects directly to the Motor Axle & is secured into position using a Magnetic Fixing Key & Locking Grub Screw.

This custom made Motor Pulley Wheel uses the German Made STRONGBELT which is 15mm wide and should never stretch or break on you whilst still providing the smoothest of power deliveries to the user even from a standing start....

Changing your Motor Pulley &/or Drive pulley wheels will drastically change the performance of your ride... :-)

The KEYWAY connects between the Motor Pulley & the Motor Axle Shaft to eliminate slip under power 3x3x8mm

TRAMPA's Motor Axle Shaft to Pulley KEYWAY measures 3 x 3 x 8mm. It connects into the Motor Pulley when mounted onto the motor Axle Shaft & is used to center the pulley on the Axle & to assist in delivering all the power from the motor without slip! This KEYWAY will fit to all TRAMPA motors amongst others.

TRAMPA's Axle length measures 38.5mm (from motor housing to end of shaft) & has a Diameter of 8mm. The centre of the key (3 x 3 x 8mm) sits 16.70mm away from the Motor front. Front side of Motor to Center of Key! Deduct 4mm & you have the length from front side of motor to the start of key....

66 Tooth Slave Pulley - Fits 15mm Belts to SUPERSTAR, HYPA & PRIMO Wheels on URBAN Motor Mounts

TRAMPA's 66 Tooth URBAN mount Slave Pulley fits to any of the HYPA, SUPERSTAR or PRIMO wheels in the TRAMPA product Range & are used when connecting electric motors to the URBAN Motor Mounts.

The 66 Tooth URBAN Slave Pulley has been precision milled from super-light-weight & mega strong Heat Treated T6 Aluminum. The pulleys teeth stand 5mm tall, this is the same size teeth as that found on TRAMPA's 15mm wide 'Strongbelt' & when TRAMPA's Premium Strongbelts are wrapped around the pulleys, using the belt tension facility to screw down & increase the tension on the belt the connection between the teeth & the belt becomes so efficient it has what we call HIGH TORQUE DRIVE (HTD)HTD ensures all of the motors Torque is forced through the pulleys to the wheels & when coupled with the amazing VESC 6 & 12s Battery power provides instant smooth unreal Power on tap to the rider!

With the use of some very special Threaded Hex Spacers & Socket capped Bolts the 66 Tooth URBAN Mount Slave Wheel connects directly into any of the GUMMIES, 6.5, 7 or 8 Inch SUPERSTAR or HYPA Wheels as well as into the PRIMO 3 spoke 9 Inch wheels to give a massive final drive... - 1 pulley, 3 uses, Amazing! :-)

TRAMPA's 66 tooth URBAN Mount Slave Wheel works in conjunction with all & any of the 13, 14 or 15 tooth Motor Pulley in the range. Changing your Motor Pulley will drastically alter the performance & characteristics of your ride... 13 Tooth is best for Hill Climbing whilst 15 Tooth is best for high speed, 14 tooth will give you all round performance...

To connect to HYPA hubs you'll need 6x 17x4mm Threaded Hex spacers
To connect to SUPERSTAR hubs you'll need 5x 15x4mm Threaded Hex spacers

To connect 6.5 & 7 Inch Wheels use 460x15mm Belt
To connect to 8 & 9 Inch Wheels use 475x15mm Belt.

In this Kit you get the following parts -
Original Urban Carve Truck Motor Mount Connector - T6 Aluminum
Urban Carver Carbon Fibre Motor Mount Panel - REGULAR
M8 x 16mm GRIPPY Grub Screw - Marine Grade Stainless Steel
TORX M5 x 16mm Countersunk Bolt - Marine Grade Stainless steel
TRAMPA ABEC 7 608 Longboard & skateboard Bearing - BLACK
Motor Axle Support for Spring Truck Motor Mounts
M4 x 16mm Socket Capped Bolt - Marine Grade Stainless Steel
14 Tooth Aluminum Motor Pulley - Best All Round Performance
M4 x 4mm Motor Pulley Grub Screw - Marine Grade Stainless Steel
KEYWAY for Motor Pulley & Axle Shaft - 3x 3x 8mm
TORX M4 x 10mm Socket Capped Bolt fitting - Marine Grade Stainless Steel
66 Tooth Slave Pulley for URBAN Motor Mounts
M4 x 17mm Threaded Hex Spacer connects 66 tooth Pulley to HYPA
TORX M4 x 10mm Socket Capped Bolt fitting - Marine Grade Stainless Steel
460 x 15mm wide 5mm (HTD) Mountainboard STRONGBELT - NO SLIP!
Weight: 385g
Are you Left Leg Forwards (Regular) or Right Leg Forwards (Goofy)?
Are you Left Leg Forwards (Regular) or Right Leg Forwards (Goofy)?
Please set me up as Left leg Forwards - REGULAR Rider Please set me up as Left leg Forwards - REGULAR Rider
Please set me up as Right Leg Forwards - GOOFY Rider Please set me up as Right Leg Forwards - GOOFY Rider
What size Motor Pulley you would like?
What size Motor Pulley you would like?
13 Tooth Motor Pulley - BEST Hill Climber 13 Tooth Motor Pulley - BEST Hill Climber
14 Tooth Motor Pulley - BEST All Round 14 Tooth Motor Pulley - BEST All Round
15 Tooth Motor Pulley - BEST Top Speed 15 Tooth Motor Pulley - BEST Top Speed
Are you fitting this kit to HYPA, SUPERSTAR or PRIMO Hubs?
Are you fitting this kit to HYPA, SUPERSTAR or PRIMO Hubs?
Im connecting Motor Mount to HYPA Hubs? Im connecting Motor Mount to HYPA Hubs?
Im connecting Motor Mount to SUPERSTAR Hubs? Im connecting Motor Mount to SUPERSTAR Hubs?
Im connecting Motor Mount to PRIMO Hubs? Im connecting Motor Mount to PRIMO Hubs?
Quantity required:
We have enough parts to make…  
RRP £125 - for the complete set

RRP Includes 20% VAT

Non-EU customers purchase tax-free

Approx price :
To see UPS shipping rates you need to login.

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon