This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.

2x Custom 9 Inch TRAMPA Wheel - Special for complete Boards

2x Custom 9 Inch TRAMPA Wheel - Special for complete Boards CUSTOM Hubs that fit 9 & 10 Inch Tyres 9 inch Tyres measure 4x 2.5x 9 Inch 230x75x with 4 Inch Rim will fit to all 4 inch Hubs 2x Custom 9 Inch TRAMPA Wheel - Special for complete Boards 9 Inch Re-enforced Inner Tube made by INNOVA - 225x65mm
RRP FROM
£85+

How to put a wheel on an Infinity or Vertigo truck

How to put a wheel on an Ultimate Truck

M4 x 45mm Socket Capped TORX Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 45mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special Bolt is specifically made for TRAMPA & is used to assemble the TRAMPA PHATLADZ HUBS. The socket capped head of the Bolt screws neatly though the Spokes & into the fixing point in the Rim, eventually screwing  into the M4 nut on the other side easly.

Weighing just 3 grams each, they are very lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

M4 x 50mm TORX Socket Capped Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 40mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special Bolt is specifically made for TRAMPA & is used to assemble the TRAMPA SUPERSTAR HUBS. The socket capped head of the Bolt screws neatly though the Spokes & into the fixing point in the Rim of the SUPERSTAR HUB eventually screwing  into the M4 nut on the other side easly.

Weighing just 3 grams each, they are very lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

USED FOR: 
 
SUPERSTAR HUBS
MEGASTAR HUBS

M4 Nyloc Nut - Marine Grade stainless steel Nylock Nut - Hub Nuts

Introducing TRAMPA's M4 (4mm Shaft) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M4 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to tighten to the M4 Socket Capped Bolts that hold the HYPA & SUPERSTAR hubs together. To fit the nuts M4 use an 8mm spanner or  8mm Ratchet Socket to turn the Nut onto the Bolt whilst holding the bolt with a 3mm Allen Key. Always ensure your Nuts & Bolts are tight before you ride!

Black Plastic Anti Dust Valve Cap

Standard dust caps to fit all inner tubes. Keep the crud out of your valves!. There is nothing worse than not being able to inflate your tyres. So ensure your Anti dirt dust caps are fitted tight!. Also fits bi-cycle valves

9 INCH Inner Tube INNOVA 9x2.5 Inch 225x65mm - fits 45 inch Rims & 9 inch tyres

INNOVA's Re-enforced 9 Inch inner tube measures 225mm x 65mm and will fit into all the of the 9 inch Tyres on the TRAMPA website. This 9 Inch Inner Tube will also fit into the tyres of other brands. Being made from slightly thicker rubber, this Inner Tube is slightly heavier than alternatives but the Inner Tube will handle much higher than recommended inflation rates... Therefore this INNOVA inner tube is ideal for heavier or pro riders seeking high inflation pressures...

This INNOVA Inner tube will fit into all known 9 inch tyres as well as most ATB Hubs on the market & it comes as expected with a "Plastic Anti Dust" Valve cap!

Punctures Suck! Its always possible to get a puncture in the environments we ride in, so always carry a spare if you don't want your day spoiling...

PHATLADS - 5 Spoke Hub Deep Dish Split Rim hub fits 6,7,8,9 & 10 Inch tyres!! Amazing

TRAMPA's AMAZING 5 Spoke PHATLADS hubs are a '2 Part Split rim', 'DEEP-DISH' (Extra wide), OFF-SET design & the latest addition to fit into TRAMPA’s amazing range of small off road wheels.

Available in a range of Painted Vibrant colours with colour co-ordinating Black TRAMPA Logo's, the PHATLAD hubs Weigh just 184g per hub (not including fixings) TRAMPA's PHATLADS are the lightest, strongest, cheapest, best choice of hub for 9” & 10” Tyres by far.

Injection molded using genuine DuPont composite materials, PHATLAD Hubs utilize a special '2 part split-rim design' that can fit any 3.75 Inch Rim Tire (6, 7, 8 Inch Diameter Tyres) & or any 4 Inch Rim tyres (9 & even 10 Inch Diameter tyre) that TRAMPA offers & pretty much any similar size tyre on the market – One amazing lightweight strong hub to fit them all will transform your ride experience for sure!

Measuring 3.75/4 (rim diameter) x2.5 Inch (rim width) the PHATLADS hubs are a half inch wider than regular 8x2 inch TRAMPA mountainboard hubs. The slimmer/inside half of the hub has straight sided, up to the edge spokes, where as the outer/fatter half of the hub is much wider & has Angled spokes. The Angled spokes give a Deep-Dish appearance whilst gaining the extra half inch width to give them the name PHATLAD's. The PHATLAD's have the same extrnal bearing housing measurement or axle space required to fit the 8x2 Inch TRAMPA hubs onto the 12mm TRAMPA axles of 34.2mm. This 'Off-Set' 34.2mm Bearing positioning means the wider hubs sit perfectly on the axle with no problems.

Increasing the Rim width increases the ground contact of any tyres fitted to them, giving a low wide look when the 6, 7 & 8 inch tyres are fitted & the PHATLADS Hubs are the perfect width fit for the larger 9 & 10 inch tyres to get maximum surface contact (GRIP) in the muddiest of conditions when contact is needed most!

Being 2.5 Inches wide but able to fit the smaller 3.75 inch tires, means that when fitting the smaller tires to the larger hubs that the profile of the tire is completely different... The wider rim will 'Stretch' the tire & give you even more surface contact, as its being stretched width-ways this will reduce the overall tire height, reducing your tire height is like changing your final gear in the drive on an E-Board & reducing the size of your wheel will give you faster acceleration but of course slower top speed.. Its interesting to try different combinations & using PHATLADS you have hundreds of combinations available to you..

TRAMPA's PHATLADS hubs will fit flawlessly to any of TRAMPA's OPEN BELT DRIVEPRO BELT DRIVE & SPUR GEAR DRIVE Motor mount setups as well as hundreds of alternative applications, it has quickly become the DIY'ers Wheel of choice....!!

There are two sets of Bolt holes running around the perimeter of the PHATLADS Hubs. The Outer set of holes are for the assembly of the Hub & require the M4 nuts being inserted into the nut housings on the thinner of the 2 parts & once the 2 parts are mated together the Shorter M4x45mm bolt should be threaded through from the fatter side of the hub tightening into then nut with a T20 TORX Key. This M4 nut is submerged & the bolt should not sit proud of the surface of its housing. 

The Inner M4x50mm T20 TORX bolt holes of the PHATLADS hubs match the same screw pattern as any of the TRAMPA Slave pulleys suiting the 62 Tooth Slave Pulley when fitted with 6 inch tyres, the 66 tooth Slave Pulley when fitted with 8 inch Tyres & 76 Tooth Slave Pulley when fitting 9 Inch tyres.... Having 2 sets of Bolt holes allows the user to be able to remove the wheel from the assembly without deflating & disassembling the wheel, meaning they can HOT-SWAP their wheel. Being able to 'Hot Swap' your wheels without taking them apart saves you lots of time when it comes to creating different rider setups, after all a board with 6 inch wheels is completely different to a board with 9 or 10 inch Wheels!

It is possible to fit either the 12mm axle 6001-2RS Bearings & 9.525mm axle 16001-2RS Bearings into the bearing housing of the PHATLAD hubs & of course Bearing reducer sleeves can be used to reduce the 12mm bearings to either 9.525mm (TRAMPA's Mini Spring Trucks & 12FIFTIES Trucks use 9.525mm Axles) or 10mm axles if your axle should be 10mm not the imperial 9.525mm TRAMPA uses. 

When fitting PHATLAD wheels on to 12mm TRAMPA Truck axles, you should install a 18.2 x 12mm Wheel Support Spacer onto the axle before then adding the first 12mm bearing, then slide on the Orange 16.5mm Internal Spoke Support spacer & then stretch on & roll into position the 10mm O-Ring. Do all that & then present the assembled wheel & carefully slide/push the hub/wheel into position. Place the 2nd bearing onto the axle & push into the assembly. Finally, screw on the 7/16ths Axle nut with your fingers & tighten up with a 16mm or 9/16ths spanner.

TRAMPA's AMAZING 5 Spoke PHATLADS hubs are a '2 Part Split rim', 'DEEP-DISH' (Extra wide), OFF-SET design & the latest addition to fit into TRAMPA’s amazing range of small off road wheels.

Available in a range of Painted Vibrant colours with colour co-ordinating Black TRAMPA Logo's, the PHATLAD hubs Weigh just 184g per hub (not including fixings) TRAMPA's PHATLADS are the lightest, strongest, cheapest, best choice of hub for 9” & 10” Tyres by far.

Injection molded using genuine DuPont composite materials, PHATLAD Hubs utilize a special '2 part split-rim design' that can fit any 3.75 Inch Rim Tire (6, 7, 8 Inch Diameter Tyres) & or any 4 Inch Rim tyres (9 & even 10 Inch Diameter tyre) that TRAMPA offers & pretty much any similar size tyre on the market – One amazing lightweight strong hub to fit them all will transform your ride experience for sure!

Measuring 3.75/4 (rim diameter) x2.5 Inch (rim width) the PHATLADS hubs are a half inch wider than regular 8x2 inch TRAMPA mountainboard hubs. The slimmer/inside half of the hub has straight sided, up to the edge spokes, where as the outer/fatter half of the hub is much wider & has Angled spokes. The Angled spokes give a Deep-Dish appearance whilst gaining the extra half inch width to give them the name PHATLAD's. The PHATLAD's have the same extrnal bearing housing measurement or axle space required to fit the 8x2 Inch TRAMPA hubs onto the 12mm TRAMPA axles of 34.2mm. This 'Off-Set' 34.2mm Bearing positioning means the wider hubs sit perfectly on the axle with no problems.

Increasing the Rim width increases the ground contact of any tyres fitted to them, giving a low wide look when the 6, 7 & 8 inch tyres are fitted & the PHATLADS Hubs are the perfect width fit for the larger 9 & 10 inch tyres to get maximum surface contact (GRIP) in the muddiest of conditions when contact is needed most!

Being 2.5 Inches wide but able to fit the smaller 3.75 inch tires, means that when fitting the smaller tires to the larger hubs that the profile of the tire is completely different... The wider rim will 'Stretch' the tire & give you even more surface contact, as its being stretched width-ways this will reduce the overall tire height, reducing your tire height is like changing your final gear in the drive on an E-Board & reducing the size of your wheel will give you faster acceleration but of course slower top speed.. Its interesting to try different combinations & using PHATLADS you have hundreds of combinations available to you..

TRAMPA's PHATLADS hubs will fit flawlessly to any of TRAMPA's OPEN BELT DRIVEPRO BELT DRIVE & SPUR GEAR DRIVE Motor mount setups as well as hundreds of alternative applications, it has quickly become the DIY'ers Wheel of choice....!!

There are two sets of Bolt holes running around the perimeter of the PHATLADS Hubs. The Outer set of holes are for the assembly of the Hub & require the M4 nuts being inserted into the nut housings on the thinner of the 2 parts & once the 2 parts are mated together the Shorter M4x45mm bolt should be threaded through from the fatter side of the hub tightening into then nut with a T20 TORX Key. This M4 nut is submerged & the bolt should not sit proud of the surface of its housing. 

The Inner M4x50mm T20 TORX bolt holes of the PHATLADS hubs match the same screw pattern as any of the TRAMPA Slave pulleys suiting the 62 Tooth Slave Pulley when fitted with 6 inch tyres, the 66 tooth Slave Pulley when fitted with 8 inch Tyres & 76 Tooth Slave Pulley when fitting 9 Inch tyres.... Having 2 sets of Bolt holes allows the user to be able to remove the wheel from the assembly without deflating & disassembling the wheel, meaning they can HOT-SWAP their wheel. Being able to 'Hot Swap' your wheels without taking them apart saves you lots of time when it comes to creating different rider setups, after all a board with 6 inch wheels is completely different to a board with 9 or 10 inch Wheels!

It is possible to fit either the 12mm axle 6001-2RS Bearings & 9.525mm axle 16001-2RS Bearings into the bearing housing of the PHATLAD hubs & of course Bearing reducer sleeves can be used to reduce the 12mm bearings to either 9.525mm (TRAMPA's Mini Spring Trucks & 12FIFTIES Trucks use 9.525mm Axles) or 10mm axles if your axle should be 10mm not the imperial 9.525mm TRAMPA uses. 

When fitting PHATLAD wheels on to 12mm TRAMPA Truck axles, you should install a 18.2 x 12mm Wheel Support Spacer onto the axle before then adding the first 12mm bearing, then slide on the Orange 16.5mm Internal Spoke Support spacer & then stretch on & roll into position the 10mm O-Ring. Do all that & then present the assembled wheel & carefully slide/push the hub/wheel into position. Place the 2nd bearing onto the axle & push into the assembly. Finally, screw on the 7/16ths Axle nut with your fingers & tighten up with a 16mm or 9/16ths spanner.

9 inch Tyres measure 4x 2.5x 9 Inch 230x75x with 4 Inch Rim will fit to all 4 inch Hubs

9” Wheels are a huge advantage when riding on challenging off-road terrain. The Larger circumference allows for a higher rolling speeds, while the extra width provides more grip.

9” PRIMO STRIKER TYRE’s design brief was styled towards fast riding on hard packed dirt surfaces. Made using a hard rubber compound with a Wide Center Bead to help achieve maximum rolling speeds. The close cut grip pattern around the sides of the tyre gives loads of grip on all kinds of changeable terrain. Using Harder Rubber makes the STRIKER Tyre very fast whilst hard-wearing.

9” INNOVA INLINE TYRE has a straight cut profile that make it the perfect grip option for easy rolling. Working best on hard surfaces, such as Skate parks, Tarmac or Asphalt. The 3mm deep INLINE grooved surface, encourages the tyre to "Track" in a straight line.

9" MUD PLUGGER TYRES are the perfect grip choice when the riding conditions turn bad & you need the maximum amount grip! The Mud-Plugger tyre has a wide center bead, giving good top end roll speed, but is also deeply grooved with aggressive Grip around its sides Mud-Pluggers works best in bad conditions!

9" DIAMOND TREAD TYRES are an amazing all-round choice for off-road riding. Hard compound rubber allows for fast rolling speeds, whilst the aggressive grip pattern provides amazing grip on both hard & soft dirt.

ALL 9” TYRES will fit TRAMPA’s PRIMO 3-SPOKE or 9” DEEPDISH MEGASTAR Hubs

2x PHATLADS 5 Spoke Deep Dish Hub
10x M4 x 45 Socket Cap TORX Bolt
10x M4 x 50 Socket Cap TORX Bolt
10x M4 Nut - Marine Grade Stainless steel Nylock Nut
2x 9 inch Tyres measure 4x 2.5x 9 Inch 230x75x with 4 Inch Rim
2x 9 INCH Inner Tube - INNOVA
2x Black Plastic Anti Dust Valve Cap
Inflated Wheel Diameter 9in
Inflated Wheel Width 2.5in
Recommended Tyre Inflation 40-60psi
Weight: 1,600g
Which 9 Inch Hubs do you want to fit?
Which 9 Inch Hubs do you want to fit?

PHATLADS
PHATLADS

OFF-SET MEGASTAR 9 Wheels (+£75)
OFF-SET MEGASTAR 9 Wheels (+£75)

DEEP-DISH MEGASTAR 9 Wheels (+£100)
DEEP-DISH MEGASTAR 9 Wheels (+£100)

Quantity required:
We have enough parts to make…  
RRP FROM £85 - per pair

Excluding VAT
HCC: 9503001000

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon