TRAMPA's 6.5 Inch URBAN TREADS High Pressure Speed Tyre is arguably the PREMIUM TYRE in the TRAMPA range of tyres. Measuring 165x45mm when fully inflated the URBAN Tyres is uniquely sized & a special mould had to be made to make it. The High Pressure speed tyre was designed specifically to fit to both of TRAMPA's amazing HYPA & SUPERSTAR hubs with the intention of radically changing the rough ride experienced by that of a regular longboard wheel....
Using a Very High TPI construction (Thousands of very Fine Threads per Inch are stitched over the outer nylon bands) the foundation & construction is incredibly strong & by using premium quality HIGH GRIP COMPOUND motorcycle rubber to cover the High TPI construction, not only is the URBAN TREADS Tyre amazingly light weight but it has performance like that to match a premium motorcycle tyre!!
The extra inflation capability on such a reduced sized tyre gives the most incredible performance to the TRAMPA fleet of boards. The Low Profiled Wide Centre Bead with High Inflation capabilities combination gives you the ability to achieve amazingly High Speeds without barely trying... Using the spring adjusters to tighten the steering, pre-loading more tension into your springs before you wish to hit high speeds will prevent potential wobble, but with enough grip on the edges to cut muddy corners or nip down hard packed off road tracks this Urban Tread tyre doesnt only handle high speeds easily but around town, down cycle paths, through alleyways & nipping through the woods,its perfect... this tyre works as an alround urban dream....
Being smaller in size, its original design intention was to be fitted specifically to the more appropriately sized URBAN CARVE range of decks, but already the boys in the workshop are eyeing them up for their what are already 8 inch wheeled mountainboards to take the new 6.5inch URBAN TREADS.... Were heading off to race around the Go-Kart track later!! :-)
TRAMPA's M4 x 35mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This Bolt is used to assemble the TRAMPA HYPA HUBS. The socket capped head of the Bolt fits neatly into the Bolt housing of the HYPA HUB marrying into the M4 nut located in the housing on the other side of the hub.
Weighing just 3 grams each these bolts are very lightweight. They look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.
You will need a 3mm Allen Key to tighten & loosen the Nuts & Bolts from the hub. Ensure all your Nuts & Bolts are tight before riding!
Introducing TRAMPA's M4 (4mm Shaft) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M4 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts.
This Nut is used to fix to tighten to the M4 Socket Capped Bolts that hold the HYPA & SUPERSTAR hubs together. To fit the nuts M4 use an 8mm spanner or 8mm Ratchet Socket to turn the Nut onto the Bolt whilst holding the bolt with a 3mm Allen Key. Always ensure your Nuts & Bolts are tight before you ride!
This special Spacer measures 12mm (id) x 16mm (od) x 18.2mm (long) & has 2 uses!. It is firstly known as the Bearing Support Spacer as this Spacer fits between the Bearings of a 6 Spoked HYPA Hub, (when mounting the HYPA wheel onto 12mm Axles) & secondly it is also known as the AXLE SUPPORT SPACER as this spacer is also used to position any of the TRAMPA wheels in the perfect position onto the axles of 12mm TRAMPA Spring trucks....
TRAMPA spacers are produced as one long tube. The Tube is Heat Treated to gain extra strength & is then Bead Polished to give the metal extra surface protection & a shiny best appearance. The tube is then cut to the exact length for precision mounting.
The following are required to build this product: